![background image](http://html1.mh-extra.com/html/daikin/ftks50bvmb/ftks50bvmb_service-manual_501473296.webp)
SiEN18-622
Ceiling Mounted Cassette Type
System Configuration
284
Timer mode START/STOP
Press the TIMER MODE START/STOP button several
times and select the mode on the display.
The display flashes.
For setting the timer stop .... “
”
For setting the timer start ... “
”
Programming time
Press the PROGRAMMING TIME button and set the time
for stopping or starting the system.
When this button is pressed, the time advances by
1 hour.
When this button is pressed, the time goes
backward by 1 hour.
Timer ON/OFF
Press the TIMER ON/OFF button.
The timer setting procedure ends.
The display “
or
” changes from flashing light to
a constant light.
Refer to figure 4 on page [1]
NOTE
•
When setting the timer OFF and On at the same time,
repeat the above procedure from 1 to 3 once again.
When the timer is programmed to stop the system after 3
hours and start the system after 4 hours, the system will stop
after 3 hours and then 1 hour later the system will start.
•
After the timer is programmed, the display shows the
remaining time.
•
Press the TIMER ON/OFF button once again to cancel
programming. the display vanishes.
Observe the following precautions to ensure the system
operates.
•
Adjust the room temperature properly for a comfortable
environment. Avoid excessive heating or cooling.
•
Prevent direct sunlight from entering a room during cooling
operation by using curtains or blinds.
•
Ventilate the room regularly.
Using the unit for long periods of time requires attentive
ventilation of the room.
•
Keep doors and windows closed. If the doors and windows
remain open, room air will flow out and cause to descrease
the effect of cooling and heating.
•
Do not place other heaters directly below the indoor unit.
They may deform due to the heat.
•
Never place objects near the air inlet and the air outlet of
the unit. It may cause deterioration in the effect or stop in
the operation.
•
Turn off the main power supply switch when it is not used
for long periods of time. When the main power switch is
turned on, some watts of electricity is being used even if
the system is not operating. Turn off the main power
supply switch for saving energy. When reoperating, turn on
the main power supply switch 6 hours before operation for
smooth running (Refer to MAINTENANCE)
•
When the display shows “
” (TIME TO CLEAN AIR
FILTER), ask a qualified service person to clean the filters
(Refer to MAINTENANCE).
Only a qualified service person is allowed to perform
maintenance
IMPORTANT
•
Before obtaining access to terminal devices, all power
supply circuits must be interrupted
•
To clean the air conditioner, be sure to stop operation, and
turn the power switch off. Otherwise, an electric shock and
injury may result.
•
Do not wash the air conditioner with water.
Doing so may result in an electric shock.
•
Be careful with a scaffold or staging.
Caution must be exercised because of work at a high
place
How to clean the air filter
Clean the air filter when the display shows “
”
(TIME TO CLEAN AIR FILTER).
It will display that it will operate for a set amount of time.
Increase the frequency of cleaning if the unit is installed in a
room where the air is extremely contaminated.
If the dirt becomes impossible to clean, change the air filter
(For changing air filter, please contact your dealer.)
7. Optimum operation
1
2
3
8. Maintenance
(For service personnel)
Summary of Contents for FTKS50BVMB
