D-Link DGS-3024 Command Line Interface Reference Manual Download

Page: 45 / 139

DGS-3024 Layer 2 Switch CLI Reference Manual

DGS-3024:4#delete trusted_host 10.48.74.121

Command: delete trusted_host 10.48.74.121

Success.

DGS-3024:4#

enable snmp traps

Purpose

Used to enable SNMP trap support.

Syntax

enable snmp traps

Description

The

enable snmp traps

command is used to enable SNMP trap

support on the Switch.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To enable SNMP trap support on the Switch:

DGS-3024:4#enable snmp traps

Command: enable snmp traps

Success.

DGS-3024:4#

disable snmp traps

Purpose

Used to disable SNMP trap support on the Switch.

Syntax

disable snmp traps

Description

This command is used to disable SNMP trap support on the
Switch.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Example Usage:

To prevent SNMP traps from being sent from the Switch:

DGS-3024:4#disable snmp traps

Command: disable snmp traps

Success.

DGS-3024:4#

Summary of Contents for DGS-3024












































































































































Search results

Summary of Contents for DGS-3024

Reviews:

Related manuals for DGS-3024

Brands by name

Popular brands

D-Link DGS-3024, Command Line Interface Reference Manual

Search results

Summary of Contents for DGS-3024

Reviews:

Related manuals for DGS-3024

Brands by name

Popular brands