D-Link DGS-3024 Page 89 Command Line Interface Reference Manual Download | Manualshive

Page: 89 / 139

background image

DGS-3024 Layer 2 Switch CLI Reference Manual

DGS-3024:4# config mirror source port 1 ingress_target port 2
egress_target port 3

Command: config mirror source port 1 ingress_target port 2 egress_target
port 3

Success.

DGS-3024:4#

enable mirror

Purpose

Used to enable a previously entered port mirroring configuration.

Syntax

enable mirror

Description

This command, combined with the

disable mirror

command below, allows

you to enter a port mirroring configuration into the Switch, and then turn the
port mirroring on and off without having to modify the port mirroring
configuration.

Parameters None.

Restrictions None.

Example usage:

To enable mirroring configurations:

DGS-3024:4#enable mirror

Command: enable mirror

Success.

DGS-3024:4#

disable mirror

Purpose

Used to disable a previously entered port mirroring configuration.

Syntax

disable mirror

Description

This command, combined with

the enable mirror

command above, allows

you to enter a port mirroring configuration into the Switch, and then turn the
port mirroring on and off without having to modify the port mirroring
configuration.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To disable mirroring configurations:

87

«
...
87
88
89
90
91
...
»

Summary of Contents for DGS-3024












































































































































Reviews:

No comments

Related manuals for DGS-3024

COOPER POWER SERIES

Brand: Eaton Pages: 32

Brand: Keithley Pages: 452

Brand: tbs electronics Pages: 2

Brand: Vector Pages: 6

Brand: VeEX Pages: 22

Brand: H-Tronic Pages: 15

Brand: Velleman Pages: 4

Brand: Dusun Pages: 18

Brand: Enable-IT Pages: 49

Brand: Byte Delight Pages: 12

LMP-2012G-SFP Series

Brand: ANTAIRA Pages: 2

Guardian Line Series

Brand: IDEM SAFETY SWITCHES Pages: 4

SAN16B-2 - TotalStorage Express Model Switch

Brand: IBM Pages: 93

Brand: ATEN Pages: 300

Brand: Shinybow USA Pages: 2

Brand: Cooper Crouse-Hinds Pages: 24

Brand: TV One Pages: 32

Brand: CYP Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands