D-Link DGS-3024 Page 133 Command Line Interface Reference Manual Download | Manualshive

Page: 133 / 139

background image

DGS-3024 Layer 2 Switch CLI Reference Manual

System 10.9.68.4    00-80-C8-2E-C7-45 Dynamic
System 10.10.27.51 00-80-C8-48-DF-AB Dynamic
System 10.11.22.145     00-80-C8-93-05-6B Dynamic
System 10.11.94.10    00-10-83-F9-37-6E Dynamic
System 10.14.82.24 00-50-BA-90-37-10 Dynamic
System 10.15.1.60 00-80-C8-17-42-55 Dynamic
System 10.17.42.153 00-80-C8-4D-4E-0A Dynamic
System 10.19.72.100 00-50-BA-38-7D-5E Dynamic
System 10.21.32.203 00-80-C8-40-C1-06 Dynamic
System 10.40.44.60 00-50-BA-6B-2A-1E Dynamic
System 10.42.73.221 00-01-02-03-04-00 Dynamic
System 10.44.67.1 00-50-BA-DA-02-51 Dynamic
System 10.47.65.25     00-50-BA-DA-03-2B Dynamic
System 10.50.8.7    00-E0-18-45-C7-28 Dynamic
System 10.90.90.90 00-01-02-03-04-00 Local
System 10.255.255.255   FF-FF-FF-FF-FF-FF Local/Broadcast

Total Entries = 20

DGS-3024:4#

clear arptable

Used to remove all dynamic ARP table entries.

Syntax

clear arptable

Description

This command is used to remove dynamic ARP table entries from
the Switch’s ARP table. Static ARP table entries are not affected.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Purpose

Example Usage:

To remove dynamic entries in the ARP table:

DGS-3024:4#clear arptable

Command: clear arptable

Success.

DGS-3024:4#

131

«
...
131
132
133
134
135
...
»

Summary of Contents for DGS-3024












































































































































Reviews:

No comments

Related manuals for DGS-3024

Brand: ABB Pages: 7

Brand: Barksdale Pages: 5

Brand: H3C Pages: 38

Brand: H3C Pages: 36

Brand: H3C Pages: 9

Brand: H3C Pages: 36

S12500X-AF Series

Brand: H3C Pages: 21

S12500X-AF Series

Brand: H3C Pages: 42

Brand: H3C Pages: 16

Brand: H-Tronic Pages: 32

Brand: wavin Pages: 4

SMALL OFFICE CyberSwitch 150

Brand: Cabletron Systems Pages: 106

Brand: DITEC Pages: 8

RMQ-Titan M30 Series

Brand: Eaton Pages: 4

FLOW BOSS VFB-DSU

Brand: VADA Pages: 17

Brand: B&B Electronics Pages: 22

Brand: NA-DE Pages: 4

Brand: Atlona Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands