D-Link DGS-3024 Command Line Interface Reference Manual Download

Page: 20 / 139

DGS-3024 Layer 2 Switch CLI Reference Manual

disable telnet

Purpose

Used to disable the Telnet protocol on the Switch.

Syntax

disable telnet

Description

This command is used to disable the Telnet protocol on the Switch.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To disable the Telnet protocol on the Switch:

DGS-3024:4#disable telnet

Command: disable telnet

Success.

DGS-3024:4#

enable web

Purpose

Used to enable the HTTP-based management software on the
Switch.

Syntax

enable web <tcp_port_number 1-65535>

Description

This command is used to enable the Web-based management
software on the Switch. The user can specify the TCP port number
the Switch will use to listen for Telnet requests.

Parameters

<tcp_port_number 1-65535>

−

The TCP port number. TCP ports

are numbered between 1 and 65535. The “well-known” port for the
Web-based management software is 80.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To enable HTTP and configure port number:

DGS-3024:4#enable web 80

Command: enable web 80

Success.

DGS-3024:4#

Summary of Contents for DGS-3024












































































































































Search results

Summary of Contents for DGS-3024

Reviews:

Related manuals for DGS-3024

Brands by name

Popular brands

D-Link DGS-3024, Command Line Interface Reference Manual

Search results

Summary of Contents for DGS-3024

Reviews:

Related manuals for DGS-3024

Brands by name

Popular brands