D-Link DGS-3024 Page 21 Command Line Interface Reference Manual Download

Page: 21 / 139

DGS-3024 Layer 2 Switch CLI Reference Manual

disable web

Purpose

Used to disable the HTTP-based management software on the
Switch.

Syntax

disable web

Description

This command disables the Web-based management software on
the Switch.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To disable HTTP:

DGS-3024:4#disable web

Command: disable web

Success.

DGS-3024:4#

save

Purpose

Used to save changes in the Switch’s configuration to non-volatile
RAM.

Syntax

save

Description

This command is used to enter the current switch configuration into
non-volatile RAM. The saved switch configuration will be loaded into
the Switch’s memory each time the Switch is restarted.

Parameters None.

Restrictions Only

administrator-level users can issue this command.

Example usage:

To save the Switch’s current configuration to non-volatile RAM:

DGS-3024:4#save

Command: save

Saving all configurations to NV-RAM... Done.

DGS-3024:4#

Summary of Contents for DGS-3024












































































































































Search results

Summary of Contents for DGS-3024

Reviews:

Related manuals for DGS-3024

Brands by name

Popular brands

D-Link DGS-3024, Command Line Interface Reference Manual

Search results

Summary of Contents for DGS-3024

Reviews:

Related manuals for DGS-3024

Brands by name

Popular brands