CTS VRGIII-31412-CW-N-DR User Manual Download Page 88

Page: 88 / 123

values in this page.

2.10.5 General Dialing Settings

Select

General Dialing Setting

from the

VoIP Management

menu.

Then, the following screen

page appears.

For details on the settings, please refer to the description of the individual section below.

General Dialing Setting

Below is a description of configuration parameters in this section.

Inter-digit Timeout

—

Specify the time for inter-digit timeout in the text box. This is the

time value allowed between two digits that are entered.

First-digit Timeout

—

Specify the time for first-digit timeout in the text box. If a user

picks up the handset without dialing a call within this specified time, the dialing tone will

be changed to busy tone.

Feature Invocation Key

—

Feature Invocation Key.

Summary of Contents for VRGIII-31412-CW-N-DR




























































































































Search results

Summary of Contents for VRGIII-31412-CW-N-DR

Reviews:

CTS VRGIII-31412-CW-N-DR, User Manual, Page: 88 / 123

Search results

Summary of Contents for VRGIII-31412-CW-N-DR

Reviews: