manualshive.com logo in svg

CTS VRGIII-31412-CW-N-DR, User Manual, Page: 24 / 123

Share
Download
CTS VRGIII-31412-CW-N-DR User Manual Download Page 24

24 

 

Management

 

－

 

The  Management  Interface  enables  the  network  administrator  to  

remotely  log  in  the  Residential  Gateway  via  the  Management  Interface

’s  IP 

address if the source IP address is allowed in the 

“Device Access” page of the 

UI.  And  if  the  Management  Interface  is  not  created  on  the  Residential 

Gateway,  the  network  administrator  can  remotely  log  in  the  Residential 

Gateway via the data Interface

’s IP address. The difference between the two 

scenarios is illustrated in the following diagram. 

 

 

 

Data

 

－

 

The data interface is the default WAN Interface of the Residential Gateway. It is 

open to remote management from the IP specified in the Device Access web 

page  when  the  management  interface  is  not  created  on  the  Residential 

Gateway. 

 

FXS1

 

－

 

The  FXS1  interface  is  a  WAN  interface  exclusive  for  the  telephone  on 

Telephony Port 1. 

 

FXS2

 

－

 

The  FXS2  interface  is  a  WAN  interface  exclusive  for  the  telephone  on 

Telephony Port 2. 

Summary of Contents for VRGIII-31412-CW-N-DR




























































































































Reviews:

No comments