manualshive.com logo in svg

CTS VRGIII-31412-CW-N-DR, User Manual, Page: 113 / 123

Share
Download
CTS VRGIII-31412-CW-N-DR User Manual Download Page 113

113 

 

 

 

And for more details, please refer to the description of the individual section below. 

 

WLAN Status

 

This is a view-only section which displays information about the wireless settings 

of the Residential Gateway. Below is a description of each item in this section.

 

 

MAC Address

 

—

 

It is the MAC address of the wireless card of the Residential Gateway.  

 

Network Mode

 

—

 

It is the network mode of the wireless network of the Residential Gateway.. 

 

Channel Number

 

—

 

It is the channel of the wireless network of the Residential Gateway. 

 

Channel Width

 

—

 

It is the wireless channel width of the Residential Gateway which is either 

20 Hz or 40 Hz. 

 

And the table in this section displays the current status of each WAN interfaces of the Residential 

Gateway. Below is the description for each column of this table.

 

 

 

2.15.4 Routing Table 

Select 

Routing Table 

from the

 Status

 sub menu bar. Then, 

Routing Table 

screen page appears 

as follows: 

 

Summary of Contents for VRGIII-31412-CW-N-DR




























































































































Reviews:

No comments