manualshive.com logo in svg

CTS VRGIII-31412-CW-N-DR, User Manual, Page: 103 / 123

Share
Download
CTS VRGIII-31412-CW-N-DR User Manual Download Page 103

103 

 

Level 

Description 

1 

Emergency

 

System is unusable.

 

2 

Alert

 

Emergent actions that must be taken immediately. 

3 

Critical

 

Critical conditions. 

4 

Error

 

Error conditions. 

5 

Warning 

Warning conditions. 

6 

Notice

 

Normal but significant conditions.

 

7 

informational

 

Keep informational events message.

 

8 

Debug 

Debug-level messages are logged.

 

 

Click 

Apply

 after you finish configuring the setting of this page. 

 

2.14.5 Diagnostics 

This  page  enables  the  network  administrator  to  use  ICMP  and  traceroute  to  check  the  network 

connectivity. The Residential Gateway supports the diagnostic tools such as ICMP and traceroute. 

It can emit ICMP Ping messages to a destination host on the Internet and see if it can receive the 

replies  from  the  host.  It  can  trace  the  path  from  the  Residential  Gateway  to  the  destination  host 

and  display  the  list  of  routers  between  Residential  Gateway  to  the  destination  host  in  this  page. 

Select 

Diagnostics

  from 

Administration 

sub  menu  bar.  Then, 

Diagnostics

  screen  page  will 

appear as follows: 

 

 

 

For details on the settings, please refer to the description of the individual section below. 

 

Ping

 

This  section  allows  you  to  use  ICMP  to  check  the  connectivity  between  the  Residential 

Gateway and a host on the Internet. Below is a description of the configuration parameters of this 

section. 

Summary of Contents for VRGIII-31412-CW-N-DR




























































































































Reviews:

No comments