manualshive.com logo in svg

CTS VRGIII-31412-CW-N-DR, User Manual, Page: 111 / 123

Share
Download
CTS VRGIII-31412-CW-N-DR User Manual Download Page 111

111 
 

 

WAN INFO.

 

— 

This is the type of the WAN interface. 

 

Type

 

— 

This is the Internet access type of this WAN interface. 

 

VLAN

 

— 

This is the VLAN ID of this WAN interface. 

 

P-Bit

 

— 

This is the P-bit value of this WAN interface. 

 

IP

 

— 

This is the IP address which this interface has. 

 

Subnet Mask

 

— 

This is the he subnet mask of this WAN interface. 

 

 

2.15.2 LAN 

This  page  displays  information  of  the  Residential  Gateway  on  the  private  network.  Select 

LAN 

from the

 Status

 sub menu bar. Then, 

WAN 

screen page appears as follows: 

 

 

 

And for more details, please refer to the description of the individual section below. 

 

LAN  Status: 

This  is  a  view-only  section  which  displays  information  about  the  the  Residential 

Gateway on the private network. Below is a description of each item in this section.

 

 

Summary of Contents for VRGIII-31412-CW-N-DR




























































































































Reviews:

No comments