manualshive.com logo in svg

CTS VRGIII-31412-CW-N-DR, User Manual, Page: 17 / 123

Share
Download
CTS VRGIII-31412-CW-N-DR User Manual Download Page 17

17 

 

Qos

 

－

 

To configure the QoS settings and the rate limit of the Residential Gateway 

 

SIP Settings

 

－

 

To configure SIP settings, such as SIP Basic/Advanced/Account Settings. 

 

VoIP  Settings

 

－

 

To  configure  VoIP  settings,  such  as  Voice,  Phone  Book,  Call  server, 

FAX and FXS port settings, etc.

 

 

TV

 

－

 

To configure the IGMP settings and to enable or disable CATV module. And this tab 

is only available for the WLAN Residential Gateway with RF module installed.

 

 

Management

 

－

 

To enable or disable Auto-provision, TR069 and SNMP for management.

 

 

Administration

 

－

 

To  configure  Device  Access,  Interface  Management,  system 

Date/Time  setting,  Syslog,  Ping  test,  User  Privilege,  Bakc/Restore,  Factory  Default  and 

Firmware Update. 

 

Status

 

－

 

To  show  the  current  status  of  each  interface  and  the  basic  information  of  the 

Residential Gateway.

 

 

And note that when a main tab appears in the dark blue background, it is currently selected. 

 

Sub Menu Bar

 Below the Main Menu Bar is the Sub Menu Bar. The Sub Menu Bar includes the 

items which are associated to the selected main tab.  

 

The area below the Sub Menu Bar includes two sub parts. 

 

Configuration  Area

  The  part  in  the  right  side  of  the  screen  page  is  the  configuration  area. 

Select a tab in the Sub Menu Bar for a feature. Then, you can find the parameters which you can 

configure for this feature in the configuration area.  

 

Section  Panel

 

This  is  a  panel  in  the  left  side  of  the  configuration  area  which  displays  the 

sections available in the configuration area. The sections are the outline for the parameters of this 

screen page. 

 

Summary of Contents for VRGIII-31412-CW-N-DR




























































































































Reviews:

No comments