manualshive.com logo in svg

CTS VRGIII-31412-CW-N-DR, User Manual, Page: 67 / 123

Share
Download
CTS VRGIII-31412-CW-N-DR User Manual Download Page 67

67 

 

Select 

DMZ

 from the 

Application

 sub menu bar. Then, 

DMZ

 screen page appears as follows: 

 

 

 

Interface  List 

This  section  displays  a  list  of  the  data  interface  and  alias  interfaces  of  the 

Residential Gateway. You can create a DMZ for each of the WAN interfaces in the list. And after a 

DMZ  is  created  for  an  interface,  this  interface  will  redirect  the  packets  received  from  the  public 

network to its DMZ. Below is a description for each column of the table.

 

 

EN 

—

 

This field displays if the WAN interface is enabled or disabled. You can click this 

field to create or edit its interface in the following section. 

 

WAN INFO. 

—

 This is a view-only field which displays the type of the WAN interface. 

 

Type

 

—

  This  is  a  view-only  field  which  displays  the  Internet  access  type  of  this  WAN 

interface. 

 

VLAN

 

—

 This is a view-only field. It displays the VLAN ID which the WAN interface will 

add to the untagged packets when the packets leave the Residential Gateway from this 

WAN interface. 

 

P-Bit

 

—

 

This  is  a  view-only  field.  It  displays  the  802.1p  priority  value  which  the  WAN 

interface will add to the untagged packets along with its VLAN ID. 

 

WAN IP

 

—

 

This is a view-only field which displays the IP address of this WAN interface. 

 

Summary of Contents for VRGIII-31412-CW-N-DR




























































































































Reviews:

No comments