manualshive.com logo in svg

CTS VRGIII-31412-CW-N-DR, User Manual, Page: 110 / 123

Share
Download
CTS VRGIII-31412-CW-N-DR User Manual Download Page 110

110 

 

2.15 Status 

Select

  Status 

in  the  Main  Menu  bar.  And  the  sub-items 

–

  WAN

, 

LAN

, 

WLAN

, 

Routing  Table

, 

Line Status

, and

 Port Status

– will show up on the sub menu bar. 

 

 

2.15.1 WAN 

This page displays information about the WAN port and the WAN interfaces. Select 

WAN 

from the

 

Status

 sub menu bar. Then, 

WAN 

screen page appears as follows: 

 

 

 

WAN

 

This is a view-only section which displays information about the WAN port

’s status and the 

WAN interfaces of the Residential Gateway. Below is a description of each item in this section. 

 

MAC  Address

 

—

  This  is  the  MAC  address  of  the  Residential  Gateway  on  the  public 

network. 

 

Packet  Info

 

— 

This is the numbers of the packets which are both transmitted (TX) and 

received (RX) by the WAN port.  

 

Default  Gateway

 

— 

This is the default gateway which the Residential Gateway has on 

the public network. 

 

DNS

 

— 

This is the DNS server which the Residential Gateway has on the public network. 

 

And  the  table  in  this  section  displays  the  current  status  of  each  WAN  interfaces  which  is 

enabled or activated. Below is the description for each column of this table. 

Summary of Contents for VRGIII-31412-CW-N-DR




























































































































Reviews:

No comments