manualshive.com logo in svg

CTS VRGIII-31412-CW-N-DR, User Manual, Page: 84 / 123

Share
Download
CTS VRGIII-31412-CW-N-DR User Manual Download Page 84

84 

 

reach  you,  this  feature  will  send  a  special  tone  to  notify  you  of  the  incoming  call.  To 

answer  the  second  incoming  call  or  switch  back  and  forth  between  two  calls,  please 

press Flash button or FlashHook once.  

 

Call  Waiting  Timeout

 

— 

Specify  the  call  waiting  timeout  time  in  the  text  box.  If  you 

would like to continue with your first call and ignore a waiting call, this is the time that the 

second caller will wait before disconnecting the waiting call. 

 

Note:  When  the  call  waiting  function  is  activated,  the  call  forward  function  will  be  deactivated.  If 

you  enable  Call  Waiting  function  and  set  up 

“Call  Forward  on  Busy  URI”  and  “Call  Forward  on 

NoAnswer URI

” at the same time, the waiting call will be disconnected instead of forwarding to the 

specified number when the time is out. 

 

Call  Forward  on  Busy  URI

 

— 

Specify  a  account  user  name  in  the  text  box.  The 

incoming call will be forwarded  to the number of the specified account  when the line is 

busy. 

 

Call  Forward  on  NoAnswer  URI

 

— 

Specify a account user name in the text box. The 

incoming  call  will  be  forwarded  to  the  number  of  the  specified  account  if  it  is  not 

answered. 

 

Call  Forward  Always  URI

 

— 

Specify a account user name to which all incoming calls 

are always forwarded.

 

 

Call  Forward  on  NoAnswer  Timeout

 

— 

Specify the timeout time for 

“Call Forward on 

NoAnswer

”. The call will be forwarded to the specified number when the specified time is 

out, 

 

Click 

Submit

 to apply your settings after you finish configuring this page. Or click 

Reset 

to clear all 

unsaved values in the check boxes. 

 

Summary of Contents for VRGIII-31412-CW-N-DR




























































































































Reviews:

No comments