manualshive.com logo in svg

CTS VRGIII-31412-CW-N-DR, User Manual, Page: 13 / 123

Share
Download
CTS VRGIII-31412-CW-N-DR User Manual Download Page 13

13 

 

1.6 LED Descriptions 

LED 

Color 

Operation  

Power 

Off 

Power is off. 

Green 

Power is functioning normally. 

STATUS 

Green 

System is ready. 

Orange 

System is not ready. 

Orange blinking 

Insert a pin or paper clip to press the Reset button for 3 
seconds to restart the device. The STATUS LED will blink 
in orange once.  
Insert a pin or paper clip to press the Reset button for 10 
seconds to reset the device to factory defaults. The 
STATUS LED will blink in orange three times. 

WAN 

Off 

The port link is off or it is up in 10Mbps. 

Green 

The link is up and works at 100Mbps. 

Orange 

The link is up and works at 1000Mbps. 

Blinking 

The traffic is present. 

LAN 1 

Off 

The port link is off or it is up in 10Mbps. 

Green 

The link is up and works at 100Mbps. 

Orange 

The link is up and works at 1000Mbps. 

Blinking 

The traffic is present. 

LAN 2 

Off 

The port link is off or it is up in 10Mbps. 

Green 

The link is up and works at 100Mbps. 

Orange 

The link is up and works at 1000Mbps. 

Blinking 

The traffic is present. 

LAN 3 

Off 

The port link is off or it is up in 10Mbps. 

Green 

The link is up and works at 100Mbps. 

Orange 

The link is up and works at 1000Mbps. 

Blinking 

The traffic is present. 

LAN 4 

Off 

The port link is off or it is up in 10Mbps. 

Green 

The link is up and works at 100Mbps. 

Orange 

The link is up and works at 1000Mbps. 

Blinking 

The traffic is present. 

Wi-Fi 

Off 

WLAN link is off. 

Green 

WLAN link is up 

Green blinking  The  traffic is present.  

WPS 

Off 

WLAN link is off. 

Green 

WPS is searching for the WPS client. 

TEL 1 

Off 

Telephony Port 1 link is off. 

Green 

The telephone of Telephony Port 1 is off the hook. 

Green Blinking  The telephone of Telephony Port 1 rings. 

TEL 2 

Off 

Telephony Port 2 link is off. 

Green 

The telephone of Telephony Port 2 is off the hook. 

Green Blinking  The telephone of Telephony Port 2 rings. 

Summary of Contents for VRGIII-31412-CW-N-DR




























































































































Reviews:

No comments