ComAp InteliDrive Mobile Global Manual Download

Page: 64 / 261

ID-Mobile Global Guide

Group: Basic settings

Note:

Default setting of Controller address is 1.

Setpoint group

Basic settings

Related FW

2.6.0

Range [units]

[-]

Default value

Step

Comm object

8637

Related applications

Config level

Standard

Setpoint visibility

Always

Description

User defined name, used for controller identification at remote phone or mobile connection.

Engine name is max 15 characters long and have to be entered manually using DriveConfig /DriveMonitor

/InteliVision software.

Note:

Engine name is not changed when new archive is loaded. Check Engine name after firmware

upgrade.

Engine Name

back to List of setpoints

Setpoint group

Basic settings

Related FW

2.6.0

Range [units]

[OFF, RUN]

Default value

OFF

Step

Comm object

8315

Related applications

Config level

Standard

Setpoint visibility

Always

Description

OFF mode controller programming mode, engine functions are blocked. PLC functions are still working.

RUN mode operational mode, all functions are active.

Note:

Mode change can be separately password protected. Mode can be changed by binary input

Remote OFF or Remote MAN.

Mode ID

back to List of setpoints

Summary of Contents for InteliDrive Mobile






































































































































































































































































Search results

Summary of Contents for InteliDrive Mobile

Reviews:

Related manuals for InteliDrive Mobile

Brands by name

Popular brands

ComAp InteliDrive Mobile, Global Manual

Search results

Summary of Contents for InteliDrive Mobile

Reviews:

Related manuals for InteliDrive Mobile

Brands by name

Popular brands