manualshive.com logo in svg

ComAp InteliDrive Mobile, Global Manual

The ComAp InteliDrive Mobile is an advanced control product designed for efficient and reliable engine management. With its user-friendly interface, users can easily operate and monitor their equipment. For a comprehensive understanding of its features, download the Global Manual from manualshive.com for free, and unleash the full potential of your machine.

Share
Download
background image

ID-Mobile Global Guide

177

Related FW

2.6.0

Related applications

AMF, MRS

Comm object

440

Description

ID-Mobile Logical Binary Output (LBO) “Display Key x” is activated when corresponding Bodas button is

pressed – see in table below. The first button does not activate the LBO Display Key 1.

LBO

Bodas button

No LBO function

1-st “round”

Display Key 2

2-nd

Display Key 3

3-rd

Display Key 4

4-th

Display Key 5

5-th

Display Key 6

6-th

Note:

Bodas keys procedures are not available in standard Bodas-1.3 firmware, it is dedicated for future

customer branches.

Display Key 8

6

back to List of LBO

Related FW

2.6.0

Related applications

AMF, MRS

Comm object

441

Description

ID-Mobile Logical Binary Output (LBO) “Display Key x” is activated when corresponding Bodas button is

pressed – see in table below. The first button does not activate the LBO Display Key 1.

LBO

Bodas button

No LBO function

1-st “round”

Display Key 2

2-nd

Display Key 3

3-rd

Display Key 4

4-th

Display Key 5

5-th

Display Key 6

6-th

Note:

Bodas keys procedures are not available in standard Bodas-1.3 firmware, it is dedicated for future

customer branches.

Display Key 9

6

back to List of LBO

Summary of Contents for InteliDrive Mobile






































































































































































































































































Reviews:

No comments

Related manuals for InteliDrive Mobile

PIETRO FIORENTINI DELTAFLUX MT100 Technical Manual preview
DELTAFLUX MT100
Brand: PIETRO FIORENTINI Pages: 16
ABC Design Tandem Instructions For Use Manual preview
Tandem
Brand: ABC Design Pages: 38
easydriver Pro Installation And Instruction Manual preview
Pro
Brand: easydriver Pages: 26
Calsense CS3000 Quick Start Manual preview
CS3000
Brand: Calsense Pages: 10
ABC Design Rodeo Instructions Manual preview
Rodeo
Brand: ABC Design Pages: 10
ABC Design Astro Instruction Manual preview
Astro
Brand: ABC Design Pages: 10
Kasco C10 Installation & Operation Manual preview
C10
Brand: Kasco Pages: 3
C Prox Ltd FP1 User Manual preview
FP1
Brand: C Prox Ltd Pages: 5
Eaton TS110 Product Manual preview
TS110
Brand: Eaton Pages: 28
Parallel Galleon Installation Manual preview
Galleon
Brand: Parallel Pages: 16
V2 EASY Series Manual preview
EASY Series
Brand: V2 Pages: 46
Paradox Magellan REM2 Reference And Installation preview
Magellan REM2
Brand: Paradox Pages: 2
Samson FOUNDATION 3730-5 Mounting And Operating Instructions preview
FOUNDATION 3730-5
Brand: Samson Pages: 132
Samson 3767 Mounting And Operating Instructions preview
3767
Brand: Samson Pages: 68
Samson 3730-2 Mounting And Operating Instructions preview
3730-2
Brand: Samson Pages: 128
Samson 3725 series Mounting And Operating Instructions preview
3725 series
Brand: Samson Pages: 68
X-POWER MULTI 1 Instruction And Installation Manual preview
MULTI 1
Brand: X-POWER Pages: 24
Samson TROVIS 3730-1 Mounting And Operating Instructions preview
TROVIS 3730-1
Brand: Samson Pages: 80

Brands by name

Popular brands

Load more brands