manualshive.com logo in svg

ComAp InteliDrive Mobile, Global Manual

The ComAp InteliDrive Mobile is an advanced control product designed for efficient and reliable engine management. With its user-friendly interface, users can easily operate and monitor their equipment. For a comprehensive understanding of its features, download the Global Manual from manualshive.com for free, and unleash the full potential of your machine.

Share
Download
background image

ID-Mobile Global Guide

38

4.2.2 GPRS Module

The module has two operation modes:

Standard GSM mode CSD (Circuit Switch Data)

GPRS mode

Selection of the mode is done by setpoint (

see

Group: Act. Calls/SMS on page 101

).

Note:

Recommended Antenna Order code:

OT1A4GXXMCX

Module

type

Operation mode

Description

Supports

ID-Mobile

GPRS

SIMCOM CSD

Standard GSM mode CSD

(Circuit Switch Data)

Alarm SMS

Drive Monitor via modem connection

SIMCIM GPRS

GPRS network – enables

connection via AirGate

Alarm SMS

AirGate

Drive Monitor (via AirGate)

WebSupervisor

Overview of supported modes and functions

IMPORTANT: For support of WebSupervisor and AirGate chose the ID-Mobile GPRS plug-in

module.

Note:

Proper function of GPRS/GPS connection depends significantly to cell network provider. Be sure your

provider supports data transfer.

IMPORTANT: Disable the PIN code on the SIM card prior applying in ID-Mobile/ID-Mobile Logger.

Note:

For further details how to install the module see GSM Assembling document in supplement.

Summary of Contents for InteliDrive Mobile






































































































































































































































































Reviews:

No comments

Related manuals for InteliDrive Mobile

IAI Msep First Step Manual preview
Msep
Brand: IAI Pages: 5
IFM CR710S Original Operating Instructions preview
CR710S
Brand: IFM Pages: 49
L-Acoustics LA4X Maintenance Manual preview
LA4X
Brand: L-Acoustics Pages: 24
L-Acoustics LA8 Maintenance Manual preview
LA8
Brand: L-Acoustics Pages: 21
M&S Systems MC960 Installation Manual preview
MC960
Brand: M&S Systems Pages: 4
Z3 Technology Z3-DM8107-SDI-RPS User Manual preview
Z3-DM8107-SDI-RPS
Brand: Z3 Technology Pages: 73
Z-Wave Control4 Setup Manual preview
Control4
Brand: Z-Wave Pages: 14
Z-Wave.Me KFOB2 Quick Start preview
KFOB2
Brand: Z-Wave.Me Pages: 4
DeLaval MPCII Memo preview
MPCII
Brand: DeLaval Pages: 102
MX Atmos Sigma Fitting Instructions Manual preview
Atmos Sigma
Brand: MX Pages: 12
Harman FG2106-04 Quick Start Manual preview
FG2106-04
Brand: Harman Pages: 2
Linear Technology LT3507 Demo Manual preview
LT3507
Brand: Linear Technology Pages: 6
Nortek WRC4 Owner'S Manual preview
WRC4
Brand: Nortek Pages: 24
Viva VRM2 Instruction Manual preview
VRM2
Brand: Viva Pages: 9
Wilo AlarmControl 1 Installation And Operating Instructions Manual preview
AlarmControl 1
Brand: Wilo Pages: 128
TCS BRE2-EB Product Information preview
BRE2-EB
Brand: TCS Pages: 8
Waeco Switch200VTO Installation And Operating Manual preview
Switch200VTO
Brand: Waeco Pages: 168
Samwon Tech TEMP880S Instuctions For Installation And Use preview
TEMP880S
Brand: Samwon Tech Pages: 104

Brands by name

Popular brands

Load more brands