manualshive.com logo in svg

ComAp InteliDrive Mobile, Global Manual

The ComAp InteliDrive Mobile is an advanced control product designed for efficient and reliable engine management. With its user-friendly interface, users can easily operate and monitor their equipment. For a comprehensive understanding of its features, download the Global Manual from manualshive.com for free, and unleash the full potential of your machine.

Share
Download
background image

ID-Mobile Global Guide

129

Analog outputs availability

Module

Number of outputs

Note

ID-Mobile

AOUT1 to AOUT8

ECU (J1939)

4 (virtual outs)

Format depends on ECU

I-AOUT8

4× 8 Analog outputs

Analog outputs configuration

The two limits “Lo limit” and “Hi limit” can be modified in DriveConfig. “Lo limit” corresponds to low Analog output

limit i.e. 0V or 0mA output and Hi limit corresponds to full range 10V or 20mA output. Lo limit and Hi limit transfer

the full internal analog value range to Analog output range.

Following is example of transfer characteristics 0 - 100% to 0 – 20mA and 4 -20mA.

Group: Analog CU

Values are shown and titled according to configuration AIN1 – AIN11 and:

Value group

Analog CU

Related FW

2.6.0

Resolution [units]

[V]

Comm object

8213

Related applications

AMF, MRS

Description

Voltage of the battery (Power source for the controller).

Battery Volt

6

back to List of values

Value group

Analog CU

Related FW

2.6.0

Resolution [units]

[°C]

Comm object

10124

Related applications

AMF, MRS

Description

Processor temperature of the controller.

CPU Temp

6

back to List of values

Group: Binary CU

Summary of Contents for InteliDrive Mobile






































































































































































































































































Reviews:

No comments

Related manuals for InteliDrive Mobile

Valve Concepts 5400 Installation, Operation And Maintenance Manual preview
5400
Brand: Valve Concepts Pages: 16
Faber JP Manual preview
JP
Brand: Faber Pages: 8
Ransburg 9040 Service Manual preview
9040
Brand: Ransburg Pages: 49
Balboa GL Series Quick Reference Manual preview
GL Series
Brand: Balboa Pages: 2
Badger Meter PC100 Installation And Operation Manual preview
PC100
Brand: Badger Meter Pages: 20
ICP DAS USA I-7188XA User Manual preview
I-7188XA
Brand: ICP DAS USA Pages: 166
ICP DAS USA SMS-531 User Manual preview
SMS-531
Brand: ICP DAS USA Pages: 64
ICS Tunnel Master Jr Manual preview
Tunnel Master Jr
Brand: ICS Pages: 83
ICP DAS USA PROFIBUS PROFI-2510 Quick Start preview
PROFIBUS PROFI-2510
Brand: ICP DAS USA Pages: 4
ICP DAS USA I-8213W-4G User Manual preview
I-8213W-4G
Brand: ICP DAS USA Pages: 40
M-Audio Axiom AIR 25 Service Manual preview
Axiom AIR 25
Brand: M-Audio Pages: 26
M Climate Bobbie Installation Instructions Manual preview
Bobbie
Brand: M Climate Pages: 12
Zamel P-257/2 Quick Manual preview
P-257/2
Brand: Zamel Pages: 2
Zamel P-257/2 Quick Start Manual preview
P-257/2
Brand: Zamel Pages: 2
Zamel P-257/2 Manual Instruction preview
P-257/2
Brand: Zamel Pages: 2
National Instruments PXIe-4302 Calibration Procedure preview
PXIe-4302
Brand: National Instruments Pages: 14
National Instruments PXIe-4302 User Manual preview
PXIe-4302
Brand: National Instruments Pages: 31
National Instruments NI-9244 User Manual And Specifications preview
NI-9244
Brand: National Instruments Pages: 50

Brands by name

Popular brands

Load more brands