manualshive.com logo in svg

ComAp IG-EE, Reference Manual, Page: 87 / 117

Share
Download
ComAp IG-EE Reference Manual Download Page 87

 

 

Inteli NT MINT, SW Version 2.6,   ©ComAp – November 2011                                                      
IGS-NT-MINT-2.6-Reference Guide.PDF 

 

87

BINARY INPUT

ForceBlock del

FORCE BLOCK

Protection

closed

BINARY INPUT

Prot. block type = Force block

closed

active

active

inactive

BinInpDelayX

 

Overspeed  

[ % ] 

Threshold for engine over speed protection. 
Step:    

1% of 

Nominal RPM

 

Range:   

0 – 200% 

Hint:

 

Engine params

: 

Starting RPM

 value is checked as under-speed level when engine is running. 

Max+CylDifPmin  [ 

°

C ] 

Max+CylDifPmin  = Maximum positive Cylinder temperature Difference at minimal gen-set Power level. 
Maximum positive deviation of one cylinder temperature from the average at the 

PminCylDifEval

 load. Alarm 

can be activated depending on Block type (set in GenConfig ->Software configuration->Analog inputs) – all 
the time or after some time after start (depends on 

RunOnlyBlkDelX

 time). 

Step:    

1 

°

C 

Range:   

0 - 32000 

°

C 

Max-CylDifPmin  [ 

°

C ]  

Max-CylDifPmin  = Maximum negative Cylinder temperature Difference at minimal gen-set Power level. 
Maximum negative deviation of one cylinder temperature from the average at the 

PminCylDifEval.

 load. 

Alarm can be activated depending on Block type (set in GenConfig ->Software configuration->Analog inputs) 
– all the time or after some time after start (depends on 

RunOnlyBlkDelX

 time). 

Step:    

1 

°

C 

Range:   

0 - 32000 

°

C

 

Max+CylDifPnom  

[ 

°

C ] 

Max-CylDifPnom  = Maximum positive Cylinder temperature Difference at nominal gen-set Power level. 
Maximum positive deviation of one cylinder temperature from the average at the 

Nomin power

. Alarm can be 

activated depending on Block type (set in GenConfig ->Software configuration->Analog inputs) – all the time 
or after some time after start (depends on 

RunOnlyBlkDelX

 time).

 

Step:    

1 

°

C 

Range:   

0 - 32000 

°

C

 

Max-CylDifPnom  

[ 

°

C ]  

Max-CylDifPnom  = Maximum negative Cylinder temperature Difference at nominal gen-set Power level. 
Maximum negative deviation of one cylinder temperature from the average at the 

Nomin power

. Alarm can 

be activated depending on Block type (set in GenConfig ->Software configuration->Analog inputs) – all the 
time or after some time after start (depends on 

RunOnlyBlkDelX

 time). 

Step:    

1 

°

C 

Range:   

0 - 32000 

°

C

 

PminCylDifEval   

[ kW – MW* ] 

Minimum gen-set Power for Cylinder temperature Difference evaluation. The protection is not evaluated, if 
the gen-set power is lower than this limit. 
Step:    

0,1 kW / 1 kW / 0,01 MW* 

Range:   

0,0 kW –  

Nominal power*

 

*Note: 

The actual setpoint units and range depend on setting of the Power format (see GenConfig manual). 

Summary of Contents for IG-EE






















































































































Reviews:

No comments