manualshive.com logo in svg

ComAp IG-EE, Reference Manual, Page: 76 / 117

Share
Download
ComAp IG-EE Reference Manual Download Page 76

 

 

Inteli NT MINT, SW Version 2.6,   ©ComAp – November 2011                                                      
IGS-NT-MINT-2.6-Reference Guide.PDF 

 

76

 

ConvCoefPulse1 - 4 

[  ]  

This setpoint adjusts the rate of increasing of the PulseCounter2 – 4 (integrating internal counters that can 
be seen at PulseCounter2-4). The setpoint assigns number of pulses (

BI:PulseCounter2 – 4

) to increase the 

PulseCounter integrating value by 1.  
Step:  

1/X 

Range:  

1 – 65000 1/X 

 

Example: 

Number of pulses on the physical input BI: PulseCounter1: 10 
ConvCoefPulse1 = 2 
 
Value of the PulseCounter1 integrating counter: 5 

Comms settings 

Gen-set name 

User-defined name, used for controller identification at remote connections. 

Gen-set name

 is max 15 

characters long and has to be entered using PC software. 

Hint: 

The setpoint can be changed using PC SW only (e.g. InteliMonitor). Gen-set name isn’t affected by 
GenConfig SW. 

Contr. address   

[  ] 

Controller CAN bus and RS-485 identification number. Each controller in the group has to have its own 
unique number. 
Step:  

1 

Range:   

1 to 32 

Hint: 

When opening Direct or Modem connection to the controller (using PC monitoring/control SW), the 

Contr. 

address 

has to correspond to the Gen-set setting in PC SW. 

RS232(1) mode 

[ DIRECT / MODEM (HW) / MODEM (SW) / MODBUS-
DIRECT / MODBUS-MDM(HW) / ECU LINK ] 

Communication protocol selection for RS232(1) line. 
DIRECT: 

Connection to a local PC running InteliMonitor. RS232 or RS485 (with internal or 
external converter) lines can be used. Set this also for IG-IB connected via RS232 line. 

MODEM (HW): 

Analog/GSM/ISDN modem connection. Select this for standard modems with HW flow 
control. If selected and no CTS signal is detected, communication may not work 
correctly. 

MODEM (SW): 

Analog/GSM/ISDN modem connection. Select this for modems without HW flow control 
– controller will use SW flow control signals XOn, Xoff, so only TxD and RxD signals 
need to be connected between the controller and the modem. 

MODBUS-DIRECT: Modbus protocol for direct connection to PLC / external SCADA terminal. 

Communication speed can be selected via setpoint 

RS232(1)MBCSpd

. 

MODBUS-MDM(HW):Modbus protocol for modem (remote) connection to PLC / external SCADA terminal. 

Communication speed can be selected via setpoint 

RS232(1)MBCSpd

. 

ECU LINK: 

Port redirected to connect the ECU with special (not J1939) interface, e.g. Cummins 
Modbus. 

Hint: 

Detail description of  Modbus protocol see in Communication guide. 
ECU LINK mode can be selected only at RS232(1) port. 

RS232(2) mode 

[ DIRECT / MODEM (HW) / MODEM (SW) / MODBUS-
DIRECT / MODBUS-MDM(HW) / ECU LINK] 

Communication protocol selection for RS232(2) line. 

Summary of Contents for IG-EE






















































































































Reviews:

No comments