manualshive.com logo in svg

ComAp IG-EE, Reference Manual, Page: 37 / 117

Share
Download
ComAp IG-EE Reference Manual Download Page 37

 

 

Inteli NT MINT, SW Version 2.6,   ©ComAp – November 2011                                                      
IGS-NT-MINT-2.6-Reference Guide.PDF 

 

37

Gen-set operation states 

Gen-set can operate in following states 
 

G

EN

-

SET STATE

 

D

ESCRIPTION

 

Init 

Controller is powerd up and configuration setting is initialized 

Not ready 

Gen-set is not ready to start or is not allowed to start 

Ready 

Gen-set is ready to run, all condition for start are fulfilled 

Prestart 

Prestart sequence in process. From closing of Prestart output to closing 
of Starter output 

Cranking 

Engine is cranking and the starter output is closed 

Pause 

Pause between start attempts is counting down 

Starting 

Starting RPM is reached 

Running 

Gen-set is running and waiting for GCB connection 

Warming 

Gen-set is running in parallel operation and gen-set load is reduced to 
Warming load 

Soft load 

Gen-set power is ramping up 

Loaded 

Gen-set is loaded 

Soft unld 

Gen-set power is ramping down 

Cooling 

State after GCB was opened and engine is not stopped 

Stop Engine 

is 

stopped 

Shutdown 

Shutdown alarm activated 

Ventil 

Gas engine – ventilation of unburned fuel when stop command comes 
during cranking with gas 

SDVentil 

Gas engine – ventilation of unburned fuel after unsuccessful start attempt

Off load 

GCB is opened, gen-set keeps running on nominal RPM 

Emerg man 

Emergency manual state 

Gen-set operation states 

Summary of Contents for IG-EE






















































































































Reviews:

No comments