manualshive.com logo in svg

ComAp IG-EE, Reference Manual, Page: 43 / 117

Share
Download
ComAp IG-EE Reference Manual Download Page 43

 

 

Inteli NT MINT, SW Version 2.6,   ©ComAp – November 2011                                                      
IGS-NT-MINT-2.6-Reference Guide.PDF 

 

43

The priority value defined by a combination of binary inputs Priority sw X is accepted with 1s delay. So if a 
change is made to more inputs simultaneously, it is accepted 1s after the last change sensed. 

GroupLink 

If the input is configured, the group linking function is active, i.e. this controller becomes the status server for 
two groups of gen-sets and informs them about the BTB status. 
If this input is closed, the controller reports BTB status as closed, if open, the controller reports open BTB 
status. 

StartButton 

Binary input has the same function as Start button on the controller front panel. It is only active in MAN mode 
and  when setpoint 

Basic settings

 -> 

Local Button

 is set to EXTBUTTONS or BOTH. 

StopButton 

Binary input has the same function as Stop button on the controller front panel. It is only active in MAN mode 
and  when setpoint 

Basic settings

 -> 

Local Button

 is set to EXTBUTTONS or BOTH. 

FaultResButton 

Binary input has the same function as Fault reset button on the controller front panel. 
To enable this function, set the setpoint 

Basic settings

 -> 

Local Button

 to EXTBUTTONS or BOTH. 

HornResButton 

Binary input has the same function as Horn reset button on the controller front panel. 

GCBButton 

Binary input has the same function as GCB  button on the controller front panel. It is active in MAN and 
TEST modes only. In TEST mode in some special cases only (see description of the TEST mode in chapter 
Mode and functions description). 

Hint: 

All Binary inputs, which simulate controller front panel buttons, are edge (no level) sensitive, and they react 
on the rising edge only. Minimal input pulse duration is 0,2 seconds. 

ManualLdRecon 

The rising edge on this input switches the controller to the lower Load Shedding stage when 

Load 

shedding:

 

AutoLd recon

 =

 DISABLED and the load is under 

Load shedding:

 

Ld recon level

. 

GCB disable 

The input blocks the GCB closing, even if all other conditions (e.g. during synchronizing) for its closing are 
fulfilled. Valid in all modes. 

Hint: 

If you want to lock out the GCB (or MCB) closing during synchronizing loop test, set 

Sync/Load ctrl:

 

Phase 

window

 = 0. This allows the control loop to be tested while actual GCB (or MCB) closing is blocked. 

Conditions for closing: 

1)  voltage only on generator side of GCB (or MCB) 
2)  voltage on both sides of GCB (or MCB) and all synchronizing conditions fulfilled. 

Alt brightness  

Active binary input switches controller display backlight to the alternative setting. Alternative intensity of the 
backlight can be set independently using the controller panel buttons. 

Hint: 

Input available in IG-NT/EE and modifications only. For IG-Display and IS-Display modules, this binary input 
is located in the Power connector and it’s function is fixed (not configurable). 

Summary of Contents for IG-EE






















































































































Reviews:

No comments