manualshive.com logo in svg

ComAp IG-EE, Reference Manual, Page: 55 / 117

Share
Download
ComAp IG-EE Reference Manual Download Page 55

 

 

Inteli NT MINT, SW Version 2.6,   ©ComAp – November 2011                                                      
IGS-NT-MINT-2.6-Reference Guide.PDF 

 

55

WrongPhSeq 

Binary output 

WrongPhSeq

 is active when at least one of following conditions is fulfilled: Generator, (Mains, 

Bus) phase is inverted or wrong generator (mains, bus) phase sequence or opposed generator phase 
sequence is detected. 

AllAvailGS run 

The output gets closed if all gen-sets available to take part in PMS are running and loaded. All gen-sets 
having the same logical group (

Pwr management

: 

Control group

) as this controller has are cons 

gen-sets from other logical groups if those are currently linked with controller’s logical group (using 
GroupLink feature). 

InMainsParal 

This LBO indicates that controller (or logical group, which the controller is member of) is connected to the 
mains. It means that there exists a way across MCB (IM-NT-MCB application) or MCB+MGCB (IM-NT-
MGCB application) to the controller. It is possible to configure this signal as MCB feedback of the controller, 
what can be useful for complicated applications with higher amount of mains. 

Hint: 

This signal works correctly only if IM-NT is used as the MCB/MGCB control device. 

TimerAct 1-4 

TimerAct 5-8 

TimerAct 9-12 

TimerAct 13-16 

These outputs are active if at least one of their assigned timer module channels gets active. Timer module 
channels are organized into groups of four. 

TimerActiveCom 

This output is a logical OR (Com = Common) of the outputs TimerAct 1-4, 5-8, 9-12, 13-16. It gets active if 
any timer module channel is active. 

kWh pulse 

The pulse with 100 miliseconds width is generated after each kWh. 

Engines swapped 

The output generates 100 ms pulse in case that two gen-sets exchange their priorities due to difference 
between Maximal running hours and Minimal running hours value (active when 

Pwr management

: 

#PriorAutoSwap

 set to RUN HOURS EQU). 

Binary outputs – Fixed protection outputs 

Alarm 

The output closes if any alarm comes up. It opens if FAULT RESET is pressed. The output closes again if a 
new fault comes up. 

Alarm flashing 

If any alarm comes up, the output starts periodic closing/opening with period 1s/1s. It opens and stays open 
if FAULT RESET is pressed. 

Horn 

The output closes if any alarm comes up. It opens if FAULT RESET or HORN RESET is pressed or if 

Engine protect:

 

Horn timeout

 has elapsed. The output closes again if a new fault comes up. 

Summary of Contents for IG-EE






















































































































Reviews:

No comments