ComAp IG-EE Reference Manual Download Page 23

Page: 23 / 117

Inteli NT MINT, SW Version 2.6, ©ComAp – November 2011
IGS-NT-MINT-2.6-Reference Guide.PDF

“Engine started” conditions

Engine speed (RPM) >

Starting RPM

AI: Oil press >

Starting POil

D+ terminal active for minimum 1s or

BI: RunIndication 1 or 2 or 3 = active or

Generator voltage > 25% of

GenNomV

(any phase)

“Engine running” conditions

RPM

Engine params

Starting RPM

Analog input Oil pressure >

Engine params

Starting POil

D+ terminal active and

Engine params

D+ function

= ENABLED or

Active Binary input RunIndication1 or

Active Binary input RunIndication2 or

Active Binary input RunIndication3 or

Vgen > 15 V (any phase).

“Still engine” conditions

Engine speed (RPM) = 0 and

AI: Oil press <

Starting POil

and

D+ terminal not active and

BI: RunIndication 1 and 2 and 3 = not active and

Generator voltage < 15V (all phases) and

Generator frequency = 0 Hz and

if all above conditions are fulfilled, additional 2s delay is necessary to confirm “still engine”

Note:

If any of the functions not used (e.g. BI RunIndication3 not configured), it’s state is omitted in the evaluation.
This is not valid for RPM comparisons, this condition is always active.

PLC functions

For PLC functions description see IGS-NT-2.6-Application guide.pdf.

Summary of Contents for IG-EE






















































































































Search results

Summary of Contents for IG-EE

Reviews:

ComAp IG-EE, Reference Manual, Page: 23 / 117

Search results

Summary of Contents for IG-EE

Reviews: