manualshive.com logo in svg

ComAp IG-EE, Reference Manual, Page: 45 / 117

Share
Download
ComAp IG-EE Reference Manual Download Page 45

 

 

Inteli NT MINT, SW Version 2.6,   ©ComAp – November 2011                                                      
IGS-NT-MINT-2.6-Reference Guide.PDF 

 

45

ExtValue1 up  

ExtValue2 up  

ExtValue3 up  

ExtValue4 up  

Active binary input causes increasing of the corresponding 

ExtValueX

 value. The rate of change is given by 

the setpoint 

ExtValueX rate

. If the 

ExtValueX

 reaches the 

ExtValueXHiLim

, the further input request is 

ignored. 

ExtValue1 down  

ExtValue2 down  

ExtValue3 down  

ExtValue4 down  

Active binary input causes decreasing of the corresponding 

ExtValueX

 value. The rate of change is given by 

the setpoint 

ExtValueX rate

. If the 

ExtValueX

 reaches the 

ExtValueXLoLim

, the further input request is 

ignored. 

Hint: 

If at least one of the inputs (

ExtValueX up

 / 

ExtValueX down

) is configured for the particular 

ExtValueX

, the 

external set commands to the same value are ignored. 

ExtValue1reset  

ExtValue2reset  

ExtValue3reset  

ExtValue4reset  

Active binary input causes 

ExtValueX

 to be reset and held at its default value, given by the setpoint 

ExtValueXdeflt

. 

Hint: 

These inputs, if configured, do not block the external set commands (in contrast to 

ExtValueX up

 / 

ExtValueX 

down 

inputs). However, if the reset input is activated, the corresponding 

ExtValueX

 is reset to its default 

(

ExtValueXdeflt

) value. This default value is kept in 

ExtValueX

 until the reset input is deactivated, and the 

external set commands received meanwhile are ignored. 

Pulse Counter 

Hint: 

Pulse width (both high/low levels) must be at least 100 ms in order to be correctly sensed! 
Conversion ratio can be selected using the setpoints 

ConvCoefPulse

. The converted values are visible in 

statistics – values 

PulseCounter

. These values can be reset using Statistics window in InteliMonitor. The 

minimum ratio beteen log. 1 and log. 0 has to be 1:1  
This Binary input is not IS-NT archives. 

Summary of Contents for IG-EE






















































































































Reviews:

No comments