manualshive.com logo in svg

ComAp IG-EE, Reference Manual, Page: 32 / 117

Share
Download
ComAp IG-EE Reference Manual Download Page 32

 

 

Inteli NT MINT, SW Version 2.6,   ©ComAp – November 2011                                                      
IGS-NT-MINT-2.6-Reference Guide.PDF 

 

32

 

Circuit breakers operation sequence, GCB fail detection 

Note: 

In the following text, “CB” abbreviation is used for GCB respectively. 

 
Related binary inputs: 

-

 

CB fdb – CB feedback binary input 

-

 

CB fdb neg – negative CB feedback binary input. Used for increasing the reliability of CB status 
evaluated by the controller. In case that it is not configured, negative value of CB fdb is calculated 
internally within the controller. 

Related binary outputs: 

-

 

CB close/open – output for circuit breaker. Equals to 1 during the time when CB is requested o be 
closed. 

-

 

CB ON coil – output for closing coil of the CB. 2s pulse (5s if synchronising is not provided by the 
particuilar CB) is used for closing the CB. 

-

 

CB OFF coil – output for opening coil of the CB. 2s pulse (5s if synchronising is not provided by the 
particuilar CB) is used for opening the CB. 

-

 

CB UV coil – output for undervoltage coil of the CB. Permanently active, 2s negative pulse (5s if 
synchronising is not provided by the particuilar CB) is used for CB opening request 

-

 

CB status – output indicating CB status as evaluated by the controller. This signal is used for lighting 
LEDs on the panel, switching the regulations, CB fail evaluation, etc. 

 
 
 
 
 
 
 
 
 
 
 

Possible CB sequences: 

 

CB close command: 

BO: CB close/open 

 

2s 

BO: CB status 

BI: CB fdb neg 

BI: CB fdb 

BO: CB ON coil 

1s 

BO: CB UV coil 

minimum 1s from UV switching on, 
together with MinStab time elapsing is 
necessary before the CB is allowed to 
close 

When closing the CB, the CB status  L
switches over only when both feedba
are in correct position 

BO 

cks 

Summary of Contents for IG-EE






















































































































Reviews:

No comments