ComAp IG-EE Reference Manual Download Page 65 | Manualshive

Page: 65 / 117

ComAp IG-EE Reference Manual Download Page 65

Inteli NT MINT, SW Version 2.6, ©ComAp – November 2011
IGS-NT-MINT-2.6-Reference Guide.PDF

65

Value Description

Dimension

InteliMonitor

IG-NT

IS-NT

SystPfCtrl

System PF control

-

YES

YES

YES

Force value group

ExtValue1-4

ExtValue1 up 1-4

x

YES

YES

YES

Load shedding group

StartLdShed

Start load shedding

-

YES

NO

NO

Hint:

Actual power request is the requested power for the actual gen-set.
*Requested engine speed is transcived value via CAN bus to ECU unit. This value is valid only when ECU
unit is configured
System load control reflects setpoint ProcessControl:

Load ctrl PtM

System PF control reflects the setpoint ProcessControl:

PF ctrl PtM

Statistics

The IGS-NT controller are equipped with statistics values. Statistics values are configurable from
InteliMonitor or GenConfig. They are visible on the controller screens.

kWhours

Is the sum of kWhours produced by the gen-set.

kVArhours

Is the sum of kVArhours produced by the gen-set.

Run hours

Number of total run hours. Run hours are counted in the Control unit only when ECU is not configured or
ECU unit does not send this statistics value. In the case of when the ECU provide Run hours controllers
statistics value Run hours is overdrawed by this value.

Num starts

Is the total sum of gen-set successful starts

NumUnscStarts

Is the total sum of gen-set unsuccessful starts

Service time X

Is the result of Service time X timer. Service Time is decremented and the actual value is visible on the
controller screen

TotalDownTime

Is sum of time when the controller is in OFF mode or any protection of second level is active or not confirmed

DnTimeReqToRun

Is the sum of time when the controller is in OFF mode or any protection of second level is active or not
confirmed and binary input Rem start/stop / Sys start/stop is simultaneously active

PulseCounter

Is the sum of pulses the control unit recognise on configured inputs.

PulseCounter X

Is the sum of pulses the control unit recognise on configured inputs.

«
...
63
64
65
66
67
...
»

Summary of Contents for IG-EE






















































































































Reviews:

No comments