manualshive.com logo in svg

ComAp IG-EE, Reference Manual, Page: 15 / 117

Share
Download
ComAp IG-EE Reference Manual Download Page 15

 

 

Inteli NT MINT, SW Version 2.6,   ©ComAp – November 2011                                                      
IGS-NT-MINT-2.6-Reference Guide.PDF 

 

15

 

System Base load 

Gen-set group is controlled on constant (or adjustable) power. The Baseload value can by changed by 
setpoint or via analog input. 
Important setpoints: 

ProcessControl

: 

#SysLdCtrlPtM

 = BASELOAD; 

#SysBaseload

; 

SysBaseLdMode. 

Local Baseload 

Selected gen-set from island or mains parallel running group can be loaded to constant 

LocalBaseload

 

value. This engine is taken out from Load sharing and Power management. 

LocalBaseload

 value is reduced 

only when common group (actual) load is lower than this value. The gen-sets in the group will try to match 
their 

LocalBaseload

s (when more than one) based on their controller addresses, so the first limited would be 

the one with the highest CAN address. I.e. this function will switch-off automatically in one or more 
controllers if there is not enough load to cover all the requested LocalBaseloads. 
Important setpoints: 

ProcessControl

: 

LocalBaseload. 

System Base power factor 

Gen-set group is controlled in mains parallel to keep a constant (or adjustable) power factor. 
Important setpoints: 

ProcessControl

: 

#SysPFCtrlPtM

 = BASEPF; 

#SysPwrFactor.

 

Import-Export 

Gen-set group is controlled to keep constant (or adjustable) Import or Export value. The external controller 
InteliMains NT must be connected on the CAN2 to control gen-set group kW I/E. 
Important setpoints: 

ProcessControl

: 

#SysLdCtrlPtM

 = LDSHARING

. 

Import/Export power factor 

Gen-set group is controlled to keep constant (or adjustable) Import or Export power factor. 
Important setpoints: 

ProcessControl

: 

#SysLdCtrlPtM

 = VSHARING

.

 The external InteliMains NT controller 

must be connected on the CAN2 to control gen-set group PF I/E. 

Engine states 

Engine prelubrication 

Engine params

: 

PrelubrTime

   PrelubrPause

Prelubr pump

Not lubricated

 

Hint:

 

To use Prelubrication, configure Binary output PRELUBR PUMP first. 
Prelubrication is disabled in controller OFF mode or if 

Prelubr time 

is set to zero. 

Binary output PRELUBR PUMP is opened when engine is running. 
Prelubrication cycle starts with 

PrelubrPause

 after engine stop. 

Summary of Contents for IG-EE






















































































































Reviews:

No comments