COBHAM EXPLORER 323 User & Installation Manual Download Page 91

Page: 91 / 158

Chapter 5: Configuration with web interface

98-169085-B

Advanced settings

1. In the

Advanced

page, click

Load/save configuration

2. Click

Save configuration

The configuration file is saved in the EXPLORER 323.

3. Click

Download configuration...

The configuration is downloaded from the EXPLORER 323 to the downloads section of
your computer.

To load a configuration from a file

To load a configuration from a file into your EXPLORER 323, do as follows:

1. In the

Advanced

page, click

Load/save configuration

2. Click

Load configuration

3. Browse to the configuration file and click

Open

The configuration is now loaded into your EXPLORER 323. When the configuration is loaded
successfully, the EXPLORER 323 restarts with the new configuration.

Summary of Contents for EXPLORER 323































































































































































Search results

Summary of Contents for EXPLORER 323

Reviews:

COBHAM EXPLORER 323, User & Installation Manual, Page: 91 / 158

Search results

Summary of Contents for EXPLORER 323

Reviews: