COBHAM EXPLORER 323 User & Installation Manual Download Page 116

Page: 116 / 158

Chapter 6: Maintenance and troubleshooting

98-169085-B

Troubleshooting

107

Connection lost

The data connection was lost.

Restart the connection e.g. from
the Dashboard in the web
interface. See

Manual

activation of data connections

on page 30.

Data or time limit exceeded

The data connection is closed
because a data limit defined in
the web interface is exceeded.
The data limit may be set to
avoid unintentional use of
bandwidth, e.g. if you forget to
close a connection after use.

Restart the connection e.g. from
the Dashboard in the web
interface. See

Manual

activation of data connections

on page 30.
You can change the data limits
in the web interface under
Advanced > Data limits.

Data rate reduction due to high
temperature

The data rate is reduced because
the temperature is too high.

Wait for the terminal to cool
down. If possible, move to a
cooler place.

Error in SIM reader

The SIM reader is not able to
read the SIM card.

Contact your supplier.

Error opening software file

A wrong file name may have
been entered with the AT
command _IUPDFW.

Use the command

_IUPDFW?

to show the correct file name
before updating.

Network failure

There is a problem with the
network, e.g. congestion.

Try again later.
If the problem persists, contact
your airtime provider.

Network failure. Reconnecting...

There is a problem, with the
network, e.g. congestion.
The terminal tries to reconnect
because it is set up for
Automatic Context Activation.

Wait for the terminal to
reconnect.
If the problem persists, contact
your airtime provider.

No connection to terminal...

The (LAN or WLAN) connection
to the terminal is lost. The
terminal may be in the process
of rebooting.

Try connecting again.
Check that you have the correct
IP address for the terminal.
See

To connect to the LAN

interface

on page 18 and

connect your WLAN-enabled
device

on page 19.

No position fix

The terminal was not able to get
a position fix from the
positioning system (GPS,
GLONASS or BeiDou)

Make sure the terminal has free
line of sight.
If the problem persists, contact
your supplier.

Displayed text

Explanation

Remedy

Summary of Contents for EXPLORER 323































































































































































Search results

Summary of Contents for EXPLORER 323

Reviews:

Related manuals for EXPLORER 323

Brands by name

Popular brands

COBHAM EXPLORER 323, User & Installation Manual

Search results

Summary of Contents for EXPLORER 323

Reviews:

Related manuals for EXPLORER 323

Brands by name

Popular brands