COBHAM EXPLORER 323 User & Installation Manual Download Page 111

Page: 111 / 158

Chapter 6: Maintenance and troubleshooting

98-169085-B

Software update

102

If you have selected

Deferred update

(_IGETFW=0), you have to use the command

_IUPDFW

followed by the file name when you want the terminal to upgrade the

software.

4. If you have selected

Immediate update

(_IGETFW=1), the terminal updates the system,

reboots, installs the update and verifies the online connection.

5. When the software upgrade is successfully completed you get an AT or SMS command

response with the message

Complete

Example:

_IUPDFW: 0, Complete

For information on software update with the web interface, see the next section.

To update software locally with the web interface

To update the software in the EXPLORER 323, do as follows:

1. Download the new software

or acquire the software from Cobham SATCOM and save it

to your computer.

2. Connect your computer to the EXPLORER 323.

3. Open the web interface in your browser.

For details on how to access the web interface, see

To access and navigate the web

interface

on page 44.

4. Click

gears

(Control panel) at the bottom of the page.

5. Click

Support > Update software

6. Click

Update software...

7. Browse to the new software version and click

Open

. The file has the extension “.tiif”.

8. The EXPLORER 323 now restarts and completes the software update.

You can check the software version under

Control panel

Support

About

1. You can download the software from the “Cobham SYNC Partner Portal” at

www.cobham.com/satcom

, select

Cobham SYNC Partner Portal

Downloads

. Locate

the EXPLORER 323 software.

Note

Connect to the LAN interface of the EXPLORER 323. Depending on your system
configuration, you may have to connect through a switch.

Note

The update procedure takes a couple of minutes.

Summary of Contents for EXPLORER 323































































































































































Search results

Summary of Contents for EXPLORER 323

Reviews:

Related manuals for EXPLORER 323

Brands by name

Popular brands

COBHAM EXPLORER 323, User & Installation Manual

Search results

Summary of Contents for EXPLORER 323

Reviews:

Related manuals for EXPLORER 323

Brands by name

Popular brands