COBHAM EXPLORER 323 User & Installation Manual Download Page 138

Page: 138 / 158

Appendix B: Command reference

98-169085-B

AT commands

129

_IUPDFW command codes

New firmware file not found

Could not find specified filename.

New firmware file corrupt

New firmware file corrupt.

New firmware file failure

The new firmware failed to run or failed to acquire the
network and the unit fell back to the old release.

Upgrade status file error

Previous update has not finished yet.

_IREMWEB command codes

Global IP: <ip_addr>

Remote connection to web interface is set up successfully.
Indicates global IP address assigned to the EXPLORER 323’s
own PDP context, to which an HTTP connection may be made.

Code Text

Explanation

Summary of Contents for EXPLORER 323































































































































































Search results

Summary of Contents for EXPLORER 323

Reviews:

Related manuals for EXPLORER 323

Brands by name

Popular brands

COBHAM EXPLORER 323, User & Installation Manual

Search results

Summary of Contents for EXPLORER 323

Reviews:

Related manuals for EXPLORER 323

Brands by name

Popular brands