COBHAM EXPLORER 323 User & Installation Manual Download Page 114

Page: 114 / 158

Chapter 6: Maintenance and troubleshooting

98-169085-B

Troubleshooting

105

Troubleshooting

Status signaling

Means of signaling

The EXPLORER 323 system provides various methods for signaling the status of the system.

•

LED

in the bottom of the EXPLORER 323 is used to signal:

• Power on/off
• Status
• Software update
• Warnings
• Errors

•

Event messages

with warnings or errors are shown in the web interface.

LED signaling

The LED is located in the cover for the SIM compartment in the bottom of the terminal.

The functions of the LED are:

Light pattern

Meaning

Green flashing rapidly

Starting up.

Yellow flashing

Antenna searching for BGAN satellite signal

Green flashing

Antenna tracking on BGAN satellite signal.

Green constant

Ready.

Yellow flashing rapidly

Closing down.

Yellow constant

Warning (user recoverable). See web interface for the warning text.

Red constant

Error. See the web interface.

Blue flashing

Uploading software to the terminal.

Blue flashing rapidly

Safe mode.

Off

Power off or Power save state.

Summary of Contents for EXPLORER 323































































































































































Search results

Summary of Contents for EXPLORER 323

Reviews:

Related manuals for EXPLORER 323

Brands by name

Popular brands

COBHAM EXPLORER 323, User & Installation Manual

Search results

Summary of Contents for EXPLORER 323

Reviews:

Related manuals for EXPLORER 323

Brands by name

Popular brands