COBHAM EXPLORER 323 User & Installation Manual Download Page 115

Page: 115 / 158

Chapter 6: Maintenance and troubleshooting

98-169085-B

Troubleshooting

106

Event messages and status messages

In the web interface of the EXPLORER 323 you can see status messages and alerts that are
currently active.

When a warning or error event is active, the web interface shows a warning symbol

warningsign

. Select

it to see a list of currently active alerts.

List of messages

The following list explains some of the messages that may show in the web interface of the
EXPLORER 323.

Displayed text

Explanation

Remedy

A destructive LTE blocker level is
detected - Rx is temporarily
switched off

A cellular network signal is
interfering severely with the
satellite signal. The LTE blocker
resilience function of the
terminal has switched off
reception of the satellite signal
(RX).

If possible, move the terminal to
another location with lower LTE
blocker level.
You can disable the LTE blocker
resilience with an AT command,
see

_ILTEBLCK

on page 130.

Antenna sky-scan malfunction

There is an error with the sky-
scan function of the antenna.

Contact your supplier

Automatic activation failed.
Reconnecting...

The terminal failed to
automatically activate a
Standard data connection at
start-up, even though it was
configured to do so.

Wait for the terminal to
reconnect.

Closing all connections due to
high temperature

High temperature is causing the
terminal to close all current
connections.

Wait for the terminal to cool
down. If possible, move to a
cooler place.

Closing terminal due to high
temperature

Critically high temperature is
causing the terminal to power
off.

Wait for the terminal to cool
down. If possible, move to a
cooler place.

Connection closed. Connection
watchdog (Link monitoring)
failure.

The terminal has closed the
connection because Link
monitoring failed.

TBD

Connection closed. Temperature
too high.

The connection is closed
because the temperature is too
high.

Wait for the terminal to cool
down. If possible, move to a
cooler place.

Connection failed

The terminal failed to establish a
connection.

Restart the connection e.g. from
the Dashboard in the web
interface. See

Manual

activation of data connections

on page 30.

Summary of Contents for EXPLORER 323































































































































































Search results

Summary of Contents for EXPLORER 323

Reviews:

Related manuals for EXPLORER 323

Brands by name

Popular brands

COBHAM EXPLORER 323, User & Installation Manual

Search results

Summary of Contents for EXPLORER 323

Reviews:

Related manuals for EXPLORER 323

Brands by name

Popular brands