COBHAM EXPLORER 323 User & Installation Manual Download Page 13

Page: 13 / 158

98-169085-B

To unpack

Chapter 2

To install the system

This chapter describes how to install the

EXPLORER 323 on a vehicle and connect cables. It has the

following sections:

•

To unpack

•

To place the terminal

•

To install the terminal

•

To connect cables

To unpack

Unpack your EXPLORER 323 and check that the following items are present:

• EXPLORER 323 Terminal with plastic spacers mounted

• Cable for combined LAN and DC power (6 m)

• Torx bit for the screws in the cover for the SIM compartment

• Mounting bolts and washers

• EXPLORER 323 Installation guide

Inspect all units and parts for possible transport damage.

Summary of Contents for EXPLORER 323































































































































































Search results

Summary of Contents for EXPLORER 323

Reviews:

Related manuals for EXPLORER 323

Brands by name

Popular brands

COBHAM EXPLORER 323, User & Installation Manual

Search results

Summary of Contents for EXPLORER 323

Reviews:

Related manuals for EXPLORER 323

Brands by name

Popular brands