manualshive.com logo in svg

Cisco ME 2400, System Message Manual, Page: 38 / 106

Share
Download
Cisco ME 2400 System Message Manual Download Page 38

 

2-26

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2      Messages and Recovery Procedures

GBIC_SECURITY Messages

Error Message   

GBIC_SECURITY-4-EEPROM_CRC_ERR: EEPROM checksum error for GBIC in 

[chars].

Explanation   

This message means that the GBIC in the specified port has invalid EEPROM data. 

[chars] is the port in which the GBIC is inserted.

Recommended Action   

Remove the GBIC from the port.

Error Message   

GBIC_SECURITY-4-EEPROM_READ_ERR: Error in reading GBIC serial ID in 

[chars]. 

Explanation   

This message means that an error occurred while the switch was reading the GBIC type 

from the EEPROM. [chars] is the port in which the GBIC is inserted.

Recommended Action   

Remove the GBIC from the port.

Error Message   

GBIC_SECURITY-4-EEPROM_SECURITY_ERR: GBIC in [chars] failed security 

check.

Explanation   

The GBIC in the specified port has invalid EEPROM data. [chars] is the port in which 

the GBIC is inserted.

Recommended Action   

Remove the GBIC from the port.

Error Message   

GBIC_SECURITY-4-GBIC_INTERR: Internal error occurred in setup for GBIC 

interface [chars]. 

Explanation   

This message means that the system could not allocate resources or had some other 

problem during the setup for the specified SFP module interface. [chars] is the interface in which 
the SFP module is installed.

Recommended Action   

Reload the switch by using the 

reload

 privileged EXEC command. If the 

problem persists, find out more about the error by using the 

show tech-support

 privileged EXEC 

command and by copying the error message exactly as it appears on the console or system log and 
entering it in the Output Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For 
more information about these online tools and about contacting Cisco, see the 

“Error Message 

Traceback Reports” section on page 1-3

. 

Error Message   

GBIC_SECURITY-6-SFP_INSERTED: Transceiver SFP [chars] module inserted 

in [chars] 

Explanation   

The online insertion and removal (OIR) facility detected a newly inserted transceiver 

module for the interface specified in the message.  The first [chars] is the module and the second 
[chars] is the interface.

Recommended Action   

No action is required.

Summary of Contents for ME 2400











































































































Reviews:

No comments