manualshive.com logo in svg

Cisco ME 2400, System Message Manual, Page: 27 / 106

Share
Download
Cisco ME 2400 System Message Manual Download Page 27

 

2-15

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2      Messages and Recovery Procedures

DOT1X Messages

Error Message   

DOT1X-5-ERR_TUNNEL: Dot1x can not be enabled on 802.1q tunnelling 

enabled ports.

Explanation   

This message means that 802.1x could not be enabled on the 802.1Q 

tunneling-enabled-port. Trying to set 802.1x port-control to 

auto

 or 

force-unauthorized

 

(force_unauth) mode on a 802.1Q-tunnel-enabled port, which is not allowed, caused this condition.

Recommended Action   

Disable 802.1Q tunneling on the interface, and then enable 802.1x.

Error Message   

DOT1X-5-ERR_VLAN_INTERNAL: The VLAN [dec] is being used internally and 

cannot be assigned for use on the Dot1x port [chars] Vlan.

Explanation   

This message means that the VLAN is used internally and cannot be assigned again for 

use on this port. [dec] is the VLAN ID. [chars] is the port number.

Recommended Action   

Update the configuration to not use this VLAN.

Error Message   

DOT1X-5-ERR_VLAN_INVALID: The VLAN [dec] is invalid and cannot be 

assigned for use on the 802.1X port [chars] Vlan.

Explanation   

This message means that the specified VLAN is out of range and cannot be assigned for 

use on this port. [dec] is the VLAN ID. [chars] is the port number.

Recommended Action   

Update the configuration to use a valid VLAN.

Error Message   

DOT1X-5-ERR_VLAN_NOT_ASSIGNABLE: RADIUS tried to assign a VLAN to 

dot1x port [chars] whose VLAN cannot be assigned.

Explanation   

This message means that the RADIUS server tried to assign a VLAN to a supplicant on 

a port whose VLAN cannot be changed, such as a routed port. [chars] is the port number.

Recommended Action   

Change the specified port to a Layer 2 port by using the 

switchport

 interface 

configuration command.

Error Message   

DOT1X-5-ERR_VLAN_NOT_FOUND: Attempt to assign non-existent [chars] 

VLAN [chars] to dot1x port [chars].

Explanation   

This message means that an attempt to assign a VLAN to a supplicant on a port fails 

because the VLAN was not found in the VTP database. [chars] is the port number.

Recommended Action   

Make sure that the VLAN exists, or use another VLAN.

Error Message   

DOT1X-5-ERR_VLAN_RESERVED: The VLAN [dec] is a reserved vlan and cannot 

be assigned for use on the Dot1x port [chars] Vlan.

Explanation   

This message means that the VLAN specified is a reserved VLAN and cannot be 

assigned for use on this port. [dec] is the VLAN ID. [chars] is the port number.

Recommended Action   

Update the configuration to not use this VLAN.

Summary of Contents for ME 2400











































































































Reviews:

No comments