manualshive.com logo in svg

Cisco ME 2400, System Message Manual, Page: 10 / 106

Share
Download
Cisco ME 2400 System Message Manual Download Page 10

 

1-2

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 1      System Message Overview

How to Read System Messages

  •

MNEMONIC is a code that uniquely identifies the message. 

  •

Message-text is a text string describing the condition. This portion of the message sometimes 
contains detailed information about the event, including terminal port numbers, network addresses, 
or addresses that correspond to locations in the system memory address space. Because the 
information in these variable fields changes from message to message, it is represented here by short 
strings enclosed in square brackets ([ ]). A decimal number, for example, is represented as [dec]. 

Table 1-2

 lists the variable fields in messages. 

This example shows a partial switch system message:

00:00:46: %LINK-3-UPDOWN: Interface Port-channel1, changed state to up

00:00:47: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to up

00:00:47: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to up

00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down 

00:00:48: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed 

state to down 2 

*Mar  1 18:46:11: %SYS-5-CONFIG_I: Configured from console by vty2 (10.34.195.36)

18:47:02: %SYS-5-CONFIG_I: Configured from console by vty2 (10.34.195.36)

*Mar  1 18:48:50.483 UTC: %SYS-5-CONFIG_I: Configured from console by vty2 (10.34.195.36) 

Table 1-1

 Message Severity Levels 

Severity Level

Description 

0 – emergency

System is unusable.

1 – alert

Immediate action required.

2 – critical

Critical condition.

3 – error

Error condition.

4 – warning

Warning condition.

5 – notification

Normal but significant condition.

6 – informational

Informational message only.

7 – debugging

Message that appears during debugging only.

Table 1-2

Representation of Variable Fields in Messages 

Representation

Type of Information

[dec]

Decimal integer

[char]

Single character

[chars]

Character string

[enet]

Ethernet address (for example, 0000.FEED.00C0)

[hex]

Hexadecimal integer

[inet]

Internet address

Summary of Contents for ME 2400











































































































Reviews:

No comments