manualshive.com logo in svg

Cisco ME 2400, System Message Manual, Page: 69 / 106

Share
Download
Cisco ME 2400 System Message Manual Download Page 69

 

2-57

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2      Messages and Recovery Procedures

QOSMGR Messages

Error Message   

PORT_SECURITY-6-ADDRESSES_REMOVED: Maximum system secure address count 

reached. Some secure addresses configured on port [chars] removed.

Explanation   

Some configured and sticky MAC addresses on the specified port were removed from 

the configuration. The number of secure addresses that the system supports was exceeded. This 
condition occurs only during hot swapping or port-mode changes (for example, when the port is 
converted from a Layer 3 to a Layer 2 port). [chars] is the port. 

Recommended Action   

No action is required. 

Error Message   

PORT_SECURITY-6-VLAN_REMOVED: VLAN [int] is no longer allowed on port 

[chars]. Its port security configuration has been removed. 

Explanation   

A configured VLAN has been excluded either due to a port-mode change or an allowed 

VLAN list change and is removed from the configuration. [int] is the VLAN ID, and [chars] is the 
switch port assigned to the VLAN. 

Recommended Action   

No action is required. 

QOSMGR Messages

This section contains the quality of service (QoS) manager messages. An incorrect QoS setting causes 
these messages.

Error Message   

QOSMGR-3-CANNOT_ERR_DISABLE_DUE_TO_INTERNAL_ERR: Can not put port in 

err-disable due to an internal error [chars].

Explanation   

This message means that an internal software error has occurred. [chars] is the 

description of the feature that the software cannot find.

Recommended Action   

Copy the message exactly as it appears on the console or in the system log. 

Research and attempt to resolve the error by using the Output Interpreter. Enter the 

show 

running-config 

user EXEC command to gather data that might help identify the nature of the error. 

Use the Bug Toolkit to look for similar reported problems. If you still require assistance, open a case 
with the TAC, or contact your Cisco technical support representative, and provide the representative 
with the gathered information. For more information about these online tools and about contacting 
Cisco, see the 

“Error Message Traceback Reports” section on page 1-3

.

Error Message   

QOSMGR-3-HW_PROGRAM_PORT_SHAPE_FAIL: Error in programming hardware for 

port shape for interface [chars].

Explanation   

This message means that an internal software error has occurred. [chars] is the 

description of the feature that the software cannot find.

Recommended Action   

Copy the message exactly as it appears on the console or in the system log. 

Research and attempt to resolve the error by using the Output Interpreter. Enter the 

show 

running-config 

user EXEC command to gather data that might help identify the nature of the error. 

Use the Bug Toolkit to look for similar reported problems. If you still require assistance, open a case 

Summary of Contents for ME 2400











































































































Reviews:

No comments