manualshive.com logo in svg

Cisco ME 2400, System Message Manual, Page: 79 / 106

Share
Download
Cisco ME 2400 System Message Manual Download Page 79

 

2-67

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2      Messages and Recovery Procedures

SPAN Messages

SPAN Messages 

This section contains the Switched Port Analyzer (SPAN) messages. 

Error Message   

SPAN-3-MEM_UNAVAIL: Memory was not available to perform the SPAN 

operation. 

Explanation   

This message means that the system was unable to perform a SPAN operation because 

of a lack of memory.

Recommended Action   

Reduce other system activity to ease the memory demands. 

Error Message   

SPAN-3-UNKN_ERR: An internal error occurred during a SPAN operation. 

Explanation   

This message means that SPAN detected an error in its internal operation.

Recommended Action   

The error might be transient. Try the SPAN operation again. If a second attempt 

also fails, reload the switch by using the 

reload

 privileged EXEC command to complete the 

operation.

Error Message   

SPAN-3-UNKN_ERR_PORT: An internal error occurred when configuring SPAN 

on port [chars]. 

Explanation   

This message means that SPAN detected an error in its internal operation. [chars] is the 

interface.

Recommended Action   

The error might be transient. Try the SPAN operation again. If the second 

attempt also fails, reload the switch by using the 

reload

 privileged EXEC command to complete the 

operation.

SPANTREE Messages

This section contains the spanning-tree messages.

Error Message   

SPANTREE-2-BLOCK_BPDUGUARD_VP: Received BPDU on port [chars], vlan 

[dec] with BPDU Guard enabled. Disabling vlan. 

Explanation   

A bridge protocol data unit (BPDU) was received on the interface and VLAN specified 

in the error message. The spanning tree BPDU guard feature was enabled and configured to shut 
down the VLAN. As a result, the VLAN was placed in the error-disabled state. [chars] is the 
interface, and [dec] is the vlan.

Recommended Action   

Either remove the device sending BPDUs, or disable the BPDU guard feature. 

The BPDU guard feature can be locally configured on the interface or globally configured on all 
ports that have Port Fast enabled. Re-enable the interface and vlan by entering the 

clear errdisable

 

privileged EXEC command.

Summary of Contents for ME 2400











































































































Reviews:

No comments