manualshive.com logo in svg

Cisco ME 2400, System Message Manual, Page: 19 / 106

Share
Download
Cisco ME 2400 System Message Manual Download Page 19

 

2-7

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2      Messages and Recovery Procedures

BACKUP_INTERFACE Messages

Error Message   

ACLMGR-3-UNLOADING: Unloading [chars] label [dec] feature. 

Explanation   

This message means that the ACL manager was unable to fit the complete configuration 

into the hardware, so some features will be applied in software. This prevents some or all of the 
packets in a VLAN from being forwarded in hardware and requires them to be forwarded by the 
CPU. Multicast packets might be dropped entirely instead of being forwarded. [chars] is the 
direction (

input

 or 

output

), and [dec] is the label number.

Recommended Action   

Use a simpler configuration. Use the same ACLs on multiple interfaces, if 

possible. 

BACKUP_INTERFACE Messages

This section contains the Flex Link message.

Error Message   

BACKUP_INTERFACE-5-VLB_NON_TRUNK: Warning:  Flexlink VLB is not 

allowed on non-trunk ports.  Please configure [chars] to be a trunk port. 

Explanation   

Flex Link VLB detects a nontrunk port. [chars] is the interface name.

Recommended Action   

Configure the interface to operate in trunking mode.

BADTRANSCEIVER Messages

This section contains the BADTRANSCEIVER message.

Error Message   

BADTRANSCEIVER, PHY, LOG_WARNING: An innapropriate transceiver has 

been inserted in interface [chars].

Explanation   

This message means that a defective module is installed in the specified interface. 

[chars] is the interface.

Recommended Action   

Remove the transceiver. If it was purchased from Cisco, contact your Cisco 

representative to have the transceiver replaced.

Summary of Contents for ME 2400











































































































Reviews:

No comments