manualshive.com logo in svg

Cisco ME 2400, System Message Manual, Page: 21 / 106

Share
Download
Cisco ME 2400 System Message Manual Download Page 21

 

2-9

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2      Messages and Recovery Procedures

DHCP_SNOOPING Messages

DHCP_SNOOPING Messages

This section contains the DHCP snooping messages.

Error Message   

DHCP_SNOOPING-3-DHCP_SNOOPING_INTERNAL_ERROR: DHCP Snooping internal 

error, [chars].

Explanation   

This message means that a software sanity check failed in the DHCP snooping process. 

[chars] is the error.

Recommended Action   

Copy the message exactly as it appears on the console or in the system log. 

Research and attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit to 
look for similar reported problems. If you still require assistance, open a case with the TAC, or 
contact your Cisco technical support representative, and provide the representative with the gathered 
information. For more information about these online tools and about contacting Cisco, see the 

“Error Message Traceback Reports” section on page 1-3

.

Error Message   

DHCP_SNOOPING-4-AGENT_OPERATION_FAILED: DHCP snooping binding 

transfer failed. [chars].

Explanation   

This message means that the DHCP snooping binding transfer process failed because of 

the specified reason for failure. [chars] is the reason for failure.

Recommended Action   

No action is required.

Error Message   

DHCP_SNOOPING-4-AGENT_OPERATION_FAILED_N: DHCP snooping binding 

transfer failed ([dec]). [chars]. 

Explanation   

This message means that the DHCP snooping binding transfer process failed because of 

the specified reason for failure [dec] is the number of failures, and [chars] is the reason for the 
failure. This message is rate-limited. 

Recommended Action   

No action is required.

Error Message   

DHCP_SNOOPING-4-DHCP_SNOOPING_ERRDISABLE_WARNING: DHCP Snooping 

received [dec] DHCP packets on interface [chars].

Explanation   

This message means that the switch detected a DHCP packet rate-limit violation on the 

specified interface and put the interface in the error-disabled state. [dec] is the number of DCHP 
packets, and [chars] is the interface.

Recommended Action   

No action is required.

Summary of Contents for ME 2400











































































































Reviews:

No comments