manualshive.com logo in svg

Cisco ME 2400, System Message Manual, Page: 55 / 106

Share
Download
Cisco ME 2400 System Message Manual Download Page 55

 

2-43

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2      Messages and Recovery Procedures

PLATFORM_PM Messages

Error Message   

PLATFORM_PBR-4-CPU_SUPPORTED_ACTION: Set action in sequence [dec] of 

route-map [chars] supported by forwarding to CPU. 

Explanation   

This message means that the route-map attached to an interface for policy-based routing 

contains an action that is not supported in hardware, so the packets are forwarded to the CPU for 
processing. The route-map actions that invoke this forwarding are 

set interface

, 

set ip default 

next-hop

,

 set default interface

, or 

set ip df

. [dec] is the action number, and [chars] is the 

route-map.

Recommended Action   

Use the 

set ip next-hop

 

ip-address

 route-map configuration command to 

reconfigure the route map action to route the packet to the specified next hop.

Error Message   

PLATFORM_PBR-4-RETRY_INSTALL: Route-map [chars] installed in hardware 

upon retry. 

Explanation   

This message means that the PBR manager was able to fit the complete configuration 

into the hardware. One or more route-maps previously failed to load because of lack of resources. 
[chars] is the route-map.

Recommended Action   

No action is required.

Error Message   

PLATFORM_PBR-4-SDM_MISMATCH: [chars] requires sdm template routing. 

Explanation   

This message means that the routing template is not enabled. [chars] is the text string 

PBR.

Recommended Action   

Modify the SDM template to enable the routing template. Use the 

sdm prefer

 

routing configuration command, and then reload the switch by using the 

reload

 privileged EXEC 

command.

PLATFORM_PM Messages

This section contains platform port manager (PM) messages.

Error Message   

PLATFORM_PM-3-IFCOUNTERROR: Unit number [dec] of interface [chars] is 

more than max allowed value of [dec]. 

Explanation   

This message means that there are too many interfaces configured for the interface type. 

[dec] is the interface count, [chars] is the interface, and [dec] is the maximum number of interfaces.

Recommended Action   

Copy the message exactly as it appears on the console or in the system log. 

Research and attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit to 
look for similar reported problems. If you still require assistance, open a case with the TAC, or 
contact your Cisco technical support representative, and provide the representative with the gathered 
information. For more information about these online tools and about contacting Cisco, see the 

“Error 

Message Traceback Reports” section on page 1-3

.

Summary of Contents for ME 2400











































































































Reviews:

No comments