manualshive.com logo in svg

Cisco ME 2400, System Message Manual, Page: 35 / 106

Share
Download
Cisco ME 2400 System Message Manual Download Page 35

 

2-23

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2      Messages and Recovery Procedures

EC Messages

Error Message   

EC-5-NOLACP: Invalid EC mode, LACP not enabled. 

Explanation   

This message means that the EtherChannel mode cannot be set because LACP is not 

included in the software image. 

Recommended Action   

Install a software image that includes LACP, and set the EC mode to 

on

.

Error Message   

EC-5-NOPAGP: Invalid EC mode, PAgP not enabled. 

Explanation   

This message means that PAgP is not included in the Cisco IOS image and that the 

EtherChannel mode cannot be set to 

desirable

 or 

auto

.

Recommended Action   

Obtain an image with PAgP included, or set the mode to 

on

 by using the 

channel-group 

channel-group-number 

mode on

 interface configuration command.

Error Message   

EC-5-PORTDOWN: Shutting down [chars] as its port-channel is 

admin-down. 

Explanation   

This message means that the administrative state of the port is controlled by the 

administrative state of its aggregate port. If the administrative state of the aggregate port is down, 
the administrative state of the port is also forced to be down. [chars] is the physical interface.

Recommended Action   

Enter the 

no shutdown 

interface configuration command on the aggregate port 

to activate the aggregation port.

Error Message   

EC-5-STAYDOWN: [chars] will remain down as its port-channel [chars] is 

admin-down.

Explanation   

This message means that the administrative state of the aggregation port overrides that 

of the affected port. If the aggregation port is administratively down, all ports in the aggregation port 
are forced to be administratively down. The first [chars] is the physical interface, and the second 
[chars] is the EtherChannel.

Recommended Action   

Enter the 

no shutdown

 interface configuration command on the aggregation 

port to activate (unshut) the aggregation port.

Error Message   

EC-5-STAYDOWN: no-shut not allowed on [chars]. Module [dec] not online.

Explanation   

This message means that an interface with an EtherChannel configuration cannot be 

enabled by using the 

no shutdown

 interface configuration command because it is a member of an 

EtherChannel group and that EtherChannel group has been administratively shut down. The 
interface has an EtherChannel configuration, but no information is available yet about its port 
channel. [chars] is the interface, and [dec] is the module.

Recommended Action   

No action is required. Wait until the module is online to find out the 

port-channel setting of the EtherChannel. 

Summary of Contents for ME 2400











































































































Reviews:

No comments