manualshive.com logo in svg

Cisco ME 2400, System Message Manual, Page: 42 / 106

Share
Download
Cisco ME 2400 System Message Manual Download Page 42

 

2-30

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2      Messages and Recovery Procedures

HCPU_PROT_MGR Messages

Error Message   

HARDWARE-3-STATS_ERROR: Statistics ID [dec] is invalid.

Explanation   

This message means that the statistics ID used is out of range. The statistics supported 

by the port ASIC are identified by an ID. [dec] is the statistics ID.

Recommended Action   

Copy the message exactly as it appears on the console or in the system log. 

Research and attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit to 
look for similar reported problems. If you still require assistance, open a case with the TAC, or 
contact your Cisco technical support representative, and provide the representative with the gathered 
information. For more information about these online tools and about contacting Cisco, see the 

“Error 

Message Traceback Reports” section on page 1-3

.

HCPU_PROT_MGR Messages

This section contains the CPU protection manager messages.

Error Message   

HCPU_PROT_MGR-4-PROGRAM_POLICER_FAIL: Could not program policer for 

port.

Explanation   

This message means that a hardware error could have occurred. 

Recommended Action   

Copy the message exactly as it appears on the console or in the system log. 

Research and attempt to resolve the error by using the Output Interpreter. Enter the 

show 

running-config 

user EXEC command to gather data that might help identify the nature of the error. 

Use the Bug Toolkit to look for similar reported problems. If you still require assistance, open a case 
with the TAC, or contact your Cisco technical support representative, and provide the representative 
with the gathered information. For more information about these online tools and about contacting 
Cisco, see the 

“Error Message Traceback Reports” section on page 1-3

.

HLFM Messages

This section contains messages from the local forwarding manager.

Error Message   

HLFM-3-MACFREE_ERROR: MAC address [enet], vlan [dec] is still 

referenced; cannot free. 

Explanation   

This message means that an attempt was made to free a MAC address before releasing 

all references to it. [enet] is the MAC address, and [dec] is the VLAN ID. 

Recommended Action   

Copy the message exactly as it appears on the console or in the system log. 

Research and attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit to 
look for similar reported problems. If you still require assistance, open a case with the TAC, or 
contact your Cisco technical support representative, and provide the representative with the gathered 
information. For more information about these online tools and about contacting Cisco, see the 

“Error 

Message Traceback Reports” section on page 1-3

.

Summary of Contents for ME 2400











































































































Reviews:

No comments