manualshive.com logo in svg

Cisco ME 2400, System Message Manual, Page: 68 / 106

Share
Download
Cisco ME 2400 System Message Manual Download Page 68

 

2-56

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2      Messages and Recovery Procedures

PORT_SECURITY Messages

Error Message   

PM-4-UNKNOWN_HOST_ACCESS: Invalid Host access value ([dec]) is 

received. 

Explanation   

This message means that the host access table is being accessed with an invalid host 

access value. [dec] is the value that is received.

Recommended Action   

Copy the message exactly as it appears on the console or in the system log. 

Research and attempt to resolve the error by using the Output Interpreter. Enter the 

show 

tech-support 

user EXEC command to gather data that might help identify the nature of the error. 

Use the Bug Toolkit to look for similar reported problems. If you still require assistance, open a case 
with the TAC, or contact your Cisco technical support representative, and provide the representative 
with the gathered information. For more information about these online tools and about contacting 
Cisco, see the 

“Error Message Traceback Reports” section on page 1-3

.

PORT_SECURITY Messages

This section contains the port security messages.

Error Message   

PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred caused 

by MAC [enet] on port [chars].

Explanation   

An unauthorized device attempted to connect on a secure port. MAC [enet] is the MAC 

address of the unauthorized device, and port [chars] is the secure port. 

Recommended Action   

Identify the device that attempted to connect on the secure port. Notify your 

network system administrator of this condition. 

Error Message   

PORT_SECURITY-2-PSECURE_VIOLATION_VLAN: Security violation on port 

[chars] due to MAC address [enet] on VLAN [dec] 

Explanation   

An unauthorized device attempted to connect on a secure trunk port. [chars] is the 

secure port, MAC [enet] is the MAC address of the unauthorized device, and [dec] is the VLAN ID. 

Recommended Action   

Identify the device that attempted to connect through the secure trunk port.  

Notify your network system administrator of this condition.

Error Message   

PORT_SECURITY-6-ADDR_REMOVED: Address [dec]:[enet] exists on port 

[chars]. It has been removed from port [chars].

Explanation   

A routed port is reconfigured as a switch port. The address in the previous switch 

configuration conflicts with the running configuration and has been deleted. [dec]:[enet] is the MAC 
address of the port. [chars] is the reconfigured port. 

Recommended Action   

No action is required.

Summary of Contents for ME 2400











































































































Reviews:

No comments