manualshive.com logo in svg

Cisco ME 2400, System Message Manual, Page: 22 / 106

Share
Download
Cisco ME 2400 System Message Manual Download Page 22

 

2-10

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2      Messages and Recovery Procedures

DHCP_SNOOPING Messages

Error Message   

DHCP_SNOOPING-4-DHCP_SNOOPING_PVLAN_WARNING: DHCP Snooping 

configuration may not take effect on secondary vlan [dec]. [chars]

Explanation   

This message means that if private VLANs are configured, the DHCP Snooping 

configuration on the primary VLAN automatically propagates to all the secondary VLANs. [dec] is 
the VLAN IDs of the secondary VLANs, and [chars] is the warning.

Recommended Action   

No action is required.

Error Message   

DHCP_SNOOPING-4-IP_SOURCE_BINDING_PVLAN_WARNING: IP source filter may 

not take effect on secondary vlan [dec] where IP source binding is configured. 

[chars].

Note

This message applies only to the Cisco ME 3400E and ME 3400 switches.

Explanation   

This message means that if private VLANs are configured, the IP-source-guard filter on 

the primary VLAN automatically propagates to all secondary VLANs. [dec] is the secondary 
VLAN, and [chars] is the warning.

Recommended Action   

No action is required.

Error Message   

DHCP_SNOOPING-4-IP_SOURCE_BINDING_NON_EXISTING_VLAN_WARNING: IP 

source binding is configured on non existing vlan [dec]. 

Note

This message applies only to the Cisco ME 3400E and ME 3400 switches.

Explanation   

The message means that an IP source binding was configured on a VLAN that has not 

been configured yet. [dec] is the VLAN.

Recommended Action   

No action is required. 

Error Message   

DHCP_SNOOPING-4-NTP_NOT_RUNNING: NTP is not running; reloaded binding 

lease expiration times are incorrect.

Explanation   

This message means that if the DHCP snooping database agent loads the DHCP 

snooping bindings and NTP is not running, the calculated lease duration for the bindings is 
incorrect.

Recommended Action   

Configure NTP on the switch to provide an accurate time and date for the 

system clock. Then disable and re-enable DHCP snooping to clear the DHCP snooping binding 
database.

Summary of Contents for ME 2400











































































































Reviews:

No comments