manualshive.com logo in svg

Cisco ME 2400, System Message Manual, Page: 32 / 106

Share
Download
Cisco ME 2400 System Message Manual Download Page 32

 

2-20

Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide

OL-9641-04

Chapter 2      Messages and Recovery Procedures

EC Messages

Error Message   

DOT1X_SWITCH-5-ERR_VLAN_RSPAN: Attempt to assign RSPAN VLAN [dec] to 

802.1x port [chars]. 802.1x is incompatible with RSPAN 

Explanation   

An attempt was made to assign a remote SPAN VLAN to an IEEE 802.1x port. Remote 

SPAN should not be enabled on a VLAN in which ports are configured with IEEE 802.1x enabled. 
[dec] is the VLAN, and [chars] is the port.

Recommended Action   

Either disable remote SPAN configuration on the VLAN, or disable IEEE 

802.1x on all the ports in this VLAN.

EC Messages

This section contains the EtherChannel, Link Aggregation Control Protocol (LACP), and Port 
Aggregation Protocol (PAgP) messages.

Error Message   

EC-4-NOMEM: Not enough memory available for [chars]. 

Explanation   

This message means that either the LACP or the PAgP EtherChannel could not obtain 

the memory it needed to initialize the required data structures. [chars] is the data structure name.

Recommended Action   

Copy the message exactly as it appears on the console or in the system log. 

Research and attempt to resolve the error by using the Output Interpreter. Enter the 

show 

tech-support 

user EXEC command to gather data that might help identify the nature of the error. 

Use the Bug Toolkit to look for similar reported problems. If you still require assistance, open a case 
with the TAC, or contact your Cisco technical support representative, and provide the representative 
with the gathered information. For more information about these online tools and about contacting 
Cisco, see the 

“Error Message Traceback Reports” section on page 1-3

.

Error Message   

EC-5-BUNDLE: Interface [chars] joined port-channel [chars]. 

Explanation   

This message means that the listed interface joined the specified EtherChannel. The first 

[chars] is the physical interface, and the second [chars] is the EtherChannel interface.

Recommended Action   

No action is required.

Error Message   

EC-5-CANNOT_ALLOCATE_AGGREGATOR: Aggregator limit reached, cannot 

allocate aggregator for group [dec].

Explanation   

This message means that a new aggregator cannot be allocated in the group. [dec] is the 

affected group.

Recommended Action   

Change the port attributes of the ports in the group so that they match and join 

the same aggregator.

Summary of Contents for ME 2400











































































































Reviews:

No comments